-
M
New Holland Knotter Troubleshooting Guide
I've replaced the twine holder. I got a new disc from cottage craft works but it doesn't fit so I'll have to return it. The shaft is too short so the gear/pin won't go on. Comparing the notches in the twine disc and the spacing between the discs, mine actually doesn't seem that bad, and it is in...- MaddrCow
- Post #29
- Forum: Implement Alley
-
M
New Holland Knotter Troubleshooting Guide
Is there a way to replace the rivet pin with a bolt? The manual mentions a special slotted head stud or cap screw?- MaddrCow
- Post #28
- Forum: Implement Alley
-
M
New Holland Knotter Troubleshooting Guide
I'm thinking I'll replace the twine disc and the twine holder and the pin that the twine holder rotates on. There's some slop in it, nothing more that the other knotter, but maybe this one is more sensitive. I will replace the hay dog spring. I think that's probably why it slides off the bill hook.- MaddrCow
- Post #23
- Forum: Implement Alley
-
M
New Holland Knotter Troubleshooting Guide
It made two bales right away. But then it slipped out of the twine discs. Think the bale chamber tension was too high. But at this point I'm kind of out of ideas.- MaddrCow
- Post #20
- Forum: Implement Alley
-
M
New Holland Knotter Troubleshooting Guide
So I was messing around with baler. 1) the twine routinely falls off the billhook. I think this *may* be from small loads during the plunges. The tension release tension release cycle works it down the bill hook. It some what relented by increasing tension at twine box. 2) I was able to get a...- MaddrCow
- Post #19
- Forum: Implement Alley
-
M
New Holland Knotter Troubleshooting Guide
Here's a link to a couple slow mo videos of the knotter running and a picture of what I mean about it "falling off the bill hook" I greatly appreciate this help so please let me know what other information I can give you. I will say, I manually put the twine back over the bill hook, and it...- MaddrCow
- Post #15
- Forum: Implement Alley
-
M
New Holland Knotter Troubleshooting Guide
The pin holding the spring on my hay dog is rusted frozen into the slot. There's no good way for my to really bang on it to get it out. I'll try a lot of heat. Was hoping somebody had a wiz-bang solution. The twine, before the knot cycle is even tripped, slips off the tip of the billhook...- MaddrCow
- Post #11
- Forum: Implement Alley
-
M
New Holland Knotter Troubleshooting Guide
Sorry, All. Yes New Holland, rightside knotter, the one by the twine bin, there is a knot in the twine brought up by the needle, but not in the one on top of the bale. It's 100% of the time, I'm using Sisal twine. When I'm totally stumped, I usually start changing things until the problem...- MaddrCow
- Post #9
- Forum: Implement Alley
-
M
New Holland Knotter Troubleshooting Guide
Hey guys. I'm hanging trouble with one knotter not knotting. What I've tried from my manual isn't helping. I thought I remember there being a comprehensive troubleshooting guide for new Holland Knotter Troubleshooting. No knot in the no. 1 tine on the passenger side Knotter. I've tried...- MaddrCow
- Thread
- Replies: 28
- Forum: Implement Alley
-
M
Wire winder guide
Do you have a manual or know how to use this? I have one just like it but I can't get it to spin right.- MaddrCow
- Post #5
- Forum: Harry Ferguson
-
M
Planting small amounts with John Deere 494
I was hoping this would be the answer. I think Maxwell house still does metal. I'll have to check the diameter. I could probably design something and get a buddy of mine to 3D print a little ramp in there. I could also put by 8 and 4 year oolds kids to work for once following me. I do...- MaddrCow
- Post #15
- Forum: Implement Alley
-
M
Planting small amounts with John Deere 494
I suppose that's true. But I'm not at the favorite seed point. But once I know what I want to plant every year that could be a good solution. Just starting the farming gig.- MaddrCow
- Post #14
- Forum: Implement Alley
-
M
Planting small amounts with John Deere 494
Not much of a solution. Unless you know where I can get sweet corn seed at a better price. Or sugar pea at less than $40/lb?- MaddrCow
- Post #3
- Forum: Implement Alley
-
M
Planting small amounts with John Deere 494
Hey guys. Looking for ideas or comments. I have a jd494a plate type planter. I'm planting pretty small amounts with it. Talking 500 seeds per row. Planted peas with it this morning. And it did great. Only issue is when it gets down to only a few (~100 or so) seeds left in the container, they...- MaddrCow
- Thread
- Replies: 17
- Forum: Implement Alley
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy