(800) 853-2651
SHOP NOW

Recent content by Marengmech

Yesterday's Tractor Forums
  1. Marengmech

    3pt 2 Bottom Moldboard Plow Identification

    Hello, Trying to identify this plow so I can try and figure out how the handle thays bent into a "U" is supposed to work. Anyone have any ideas? Has super Chief x series bottoms, and after a little research, leads me believe its an old IH plow. Maybe a 420? Im probably wrong. Thought i...
  2. Marengmech

    1952 Farmall A

    Im going to hook everything up today and give it a try, see if I can get spark. If not, I will definitely be reaching out, as my expertise is very limited with this older stuff.
  3. Marengmech

    1952 Farmall A

    Hello, So I finally got the Farmall A i to my shop. Removed the secondary coil. Ordered new distributor cap, rotor button, coil and points. Took the distributor cap off, and the new one is not the same. Not is the rotor button. So going to try with the old ones. However, I have some...
  4. Marengmech

    1952 Farmall A

    Speaking with the previous owner, he installed the external coil because of no spark. He is not sure if he has it hooked up right. I think best thing is to remove external coil and put back to original, and start from there
  5. Marengmech

    1952 Farmall A

    Is there a way to check year with serial number?
  6. Marengmech

    1952 Farmall A

    It does not have hydralic lift. Will post pics tommorow
  7. Marengmech

    1952 Farmall A

    Just picked up a 52 Farmall A. 6 Volt positive ground. Worked fine last year, but currently not starting. Does anyone have any info on the ignition systems for these tractors. Previous owner says it lost spark. Thanks in advance
  8. Marengmech

    1957 B250 fuel leak

    Good morning, I noticed my fuel pump is leaking fuel after being shut down. Is this normal? Leaking from here. Thanks in advance.
  9. Marengmech

    1957 international B250 PTO lever and hydraulic question

    For the PTO I was thinking taking the lever off and adding material to build up the rounded edge.
  10. Marengmech

    1957 international B250 PTO lever and hydraulic question

    Hello, I have a 1957 International B250. I have 2 questions. First is the PTO lever. I found when using a brush hog, the lever woukd pop out and the PTO woukd disengage. The end seems rounded. Is this normal. Pic is attached. Second question. This tractor had a homemade loader added...
  11. Marengmech

    Massey Ferguson number 9 baler

    I currently don't have a manual. Would anyone have a copy of those pages, as i am trying to get everything ready for this year's having season. Just to hold me over till I can get a book in.
  12. Marengmech

    Massey Ferguson number 9 baler

    That's what we have been doing, it's almost like the arm isn't coming all the way back
  13. Marengmech

    Massey Ferguson number 9 baler

    Have a MF No 9 Baler that when knotter is engaged it is jaming up at the end of the knotting cycle and breaking the shear pin. When manually finish the rotation by pulling up on the arm for the needles it pops up no problem. Any ideas?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top