(800) 853-2651
SHOP NOW

Recent content by mark everett

Yesterday's Tractor Forums
  1. M

    Model M crawler engine

    First off i would say radiator is blocked and or water pump not working.2nd the govener rod is stuck is the slide and will not move you have to free it the try again,Also if you have had the carb off make sure the little tab is located in the correct place on the cross shaft,or 1 last thing the...
  2. M

    Allis B

    email me [email protected] i am in the uk.
  3. M

    Crawler Model M series, 32-42, w/6' dozer blade

    Worth that in spares
  4. M

    Allis Chalmers M crawler

    i can check but may take a bit of time as away at moment
  5. M

    Allis Chalmers M crawler

    There is no thread count you adjust untill lever snaps over cams wich a click.
  6. M

    Allis Chalmers 1938 M crawler engine

    No wool used that i am aware of and i have rebuilt several U M engines
  7. M

    Allis Chalmers 1938 M crawler engine

    Main bearings should have a clearence of .001 to .003 thou according to my M service book,Rod end clearence .001 -.008 thou again according to service book.Radiator bolts 5/8x1-1/2 unc.Front hook bolts 3/4 x 4-1/4 unf qty 2 and 2 5/8x3-1/2.
  8. M

    Allis dozer

    That would be a HD9X oil field tractor.
  9. M

    1936 wc rims

    1ST WC,S up to s/n 24000 had 500/525x17 F H rims i think.After 24000 they were six lug pressed steel then later 5 lug.
  10. M

    Allis Chalmers Model K Crawler

    depending on year of crawler, late crawlers the serial no is in two places on rear right side on transmisson case and on dash panel in front of steering levers or if early k on top of transmisson case, engine no is on the left side just below oil filter,or if like our k it has no engine no!!!!
  11. M

    WC tire-rim question

    i have a allis u that i removed the original tyres from and they were marked 13x28 replaces 11.25x28 i still have these tyres on a wc AND THE MODERN SIZE TO A 13X28 IS A 14.9X28 OR ULTRA MODERN 420/85X28 i have been in the tyre industry for 25 years mainly agricultural so i have some idea what i...
  12. M

    D 272

    Yes it is fitted with a perkins p3 144 it is fitted with the later engine fitted with lucas starter and generator.
  13. M

    clutch brake

    It shouldnt need a puller to remove most i have ever used is a couple of pry bars to get it to move then some spray oil and keep moveing back and forth then slides right off,if you need any more advice email me on [email protected]
  14. M

    clutch brake

    it will only come off if you undo the 3/8 pinch bolt wich is locked with lockwire it will only come right off if engine is removed cannot be removed with engine installed,once pinch bolt is unscrewed it will just slide of,well all of the 6 i have done have.
  15. M

    final drive seals for AC HD 10 dozer

    sorry no is wrong it is 507 787 2338
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top