(800) 853-2651
SHOP NOW

Recent content by Mark Lehmer

Yesterday's Tractor Forums
  1. M

    Generator field coils question.

    Thanks I will give that a good read. I ran across a old book that showed testing with 110 volts I?ve done that before, very interesting. Works very well for continuity tests. I?m thinking the what I have is what they called bucking fields , they used in marine application .
  2. M

    Generator field coils question.

    Looking for info on field coils, got a 6 volt auto-lite 3 brush GBM 4804 it has a extra wire on one half, why and where does it hook to ? The ones I?ve worked on always had one wire on each half. This has two on one side and one on the other, any help would be appreciated.
  3. M

    SC Case generator

    I?ve got a generator I want to put on my SC , Its a Auto-lite GBM 4804 6 volt . I tore it down and the fields are different than what I?m used to seeing. One half has 2 wires the other half has one wire I believe it goes to the field , but the other two I?m not sure about, the brushes were gone...
  4. M

    PTO cover

    I think the WC had a packing nut as with the early WD, and shaft size was a bit larger than the later WD and WD45 that had the seal with a smaller output shaft, they used packing in the WC and early WD. I think the whole PTO unit will interchange , if you change the engagement arm.
  5. M

    pic of plow I picked up today

    yes it has the grease cups , I'm going to clean them out and put fresh grease in them ,I ordered a manual yesterday. thanks Mark
  6. M

    pic of plow I picked up today

    that looks great ! I can do that
  7. M

    pic of plow I picked up today

    thanks, plan on a parade or two after restoration. Did not want it to come loose into a crowd . Seen this guy with a horse and buggy back down the side of a nice restored Ford, those axel nuts do a lot of damage . I gave $250 for this one, are 2-12 plows common?
  8. M

    pic of plow I picked up today

    Went to Columbus Nebraska today and got this old Centennial Plow its a 2-12" trip can anyone tell me how it stays hooked up to the tractor ? New project, the wife so happy
  9. M

    Ready for the county fair !

    Great looking , should turn some heads , you should be proud ! Alot of hard work to get it in that shape and keep it there. NICE !!!!
  10. M

    Got the SC ready for the Independence Day Parade

    Pastor John , they make that stack in 48 inch also the one I got was 24. I enjoyed all the posts you and your brother did changing to S gears, something I might consider later . If you like a little bling I put diamond plate on the steps , easy job saves on the paint there to. Thanks Mark
  11. M

    Got the SC ready for the Independence Day Parade

    Thanks Kurt, the stack came from Walts Tractor, it looks a lot better than the Stanley and keeps the paint job cleaner.
  12. M

    Got the SC ready for the Independence Day Parade

    Never seen a Case in the local parade, this will give the JD guys something to talk about!
  13. M

    What pins used with swinging drawbar??

    try it again
  14. M

    What pins used with swinging drawbar??

    This is what I made for my SC
  15. M

    1951 SC project

    thanks for the reply, hope to bring it Lathrop MO for the Case expo in June
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top