(800) 853-2651
SHOP NOW

Recent content by Mark Pengelly

Yesterday's Tractor Forums
  1. M

    930 cab fit on a 941?

    I am guessing a cab from a 930 fits a 941?
  2. R

    wc governor

    I have a wc engine and I am wondering how much more hp or rpm do you get by switching to a d17 governor spring vs putting in a 175 spring. Also I have two different governors laying around and was wondering why they have different styles. They both look like the wc/wd's. they both have the same...
  3. M

    saddens me

    received a phone call from an old friend today informing me that the Board of trustees that run the Eastern States Exposition in West Springfield Mass also known as New Englands great state fair has decided to cancel our Antique tractor display at the fair, as they are now going to rent the...
  4. J

    Looking for photo, Allis Chalmer with 2 water barrels

    In the 60s and 70s Several farms around here used Allis Chalmer snap coupler tractors to plant tobacco. There were green brackets that bolted to each side of the engine to install 2 to 4 55 gallon drums of water for the transplanter. I have been looking for a photo, have not found one. I think I...
  5. M

    model A 1950 starts when cold, stops when warm

    OK next update. Points, rotor cap and condenser for the Wico XH-1042 arrived in post today. Good service from www.magneto.co.uk in the UK all fitted along with some different spark plugs just for luck, NGK replaced the Autolite 386's. After quite a bit of cranking she started. I have the...
  6. M

    model A 1950 starts when cold, stops when warm

    Thanks all for your encouragement. Update: OK so I"m pinning my hopes on the new condenser. not easy getting these Wico parts this side of the pond(!), but found a v helpful guy from the (beautiful) county of Devon (my home) who has condenser, points and rotor cap all in stock. Sadly didn't...
  7. M

    model A 1950 starts when cold, stops when warm

    Dear All, THANKS so much for your prompt and helpful replies. Excuse the timelag in my reply - I'm UK based, just got up! To respond to your replies: My 1950 A has a Mag - although I have always suspected that it would have originally had dizzy/coil perhaps? (SN 649004) It also has a...
  8. M

    model A 1950 starts when cold, stops when warm

    I"ve scoured the forum to find something like my problem which is that when stone cold the old girls fires up fine. All appears to be well. Ignition timing, spark, carb all seem OK. After running for about 5-10 mins it all goes pear-shaped. Tractor stalls when more power required (load needle...
  9. M

    switch key purpose late model A

    THANKS everyone for your comments and replies. I think it"s John T"s and Kent P"s replies that are really getting to the heart of my question. Perhaps I should have said that I"ve just about finished restoring this tractor (just lights and decals to do) and I"m trying to be as original as...
  10. M

    switch key purpose late model A

    Can anyone help clarify how my key switch on my late styled 1950 A is supposed to work please? I think I have a mag system: a WICO model X, type XH-1042 and a generator with number 99 70 GD 1755 on it. It"s setup up with positive ground 12v To kill this tractor I have to ground the post on the...
  11. M

    sourcing special bolts and screws

    A photo of your spare old bolts would be appreciated Bernard. mcMaster will not supply me in UK... mark AT pengelly DOT info Whilst on the subject of nuts and bolts can anyone say how many of the studs and special rounded hex nuts should fill the equipment mounting holes on the rear axle of...
  12. M

    sourcing special bolts and screws

    Now that is strange about that 19H442 part no. at the JDParts website. If I go straight to it www.jdparts.com before I login it searches and finds the part fine. If i login first however and then try no joy. I suspect this is a regionalization issue for the website, ie it knows I'm not a US...
  13. M

    sourcing special bolts and screws

    Thanks everybody for the prompt replies... The suggestions for suppliers are much appreciated. Fixerupper - do you have a part No. for the corn header bolts? Duane - I did see the wheel bolts on jdparts, they list at £33 (in UK) I thought there must be a mistake! Too rich for me. I think I...
  14. M

    sourcing special bolts and screws

    Couldn't see reference on the forum to a discussion about part no. A2961R It's the square head 5/8 UNF bolt (2 1/4" long) used to hold my (late model A) hub to the cast disk wheel. Anyone know where I could get hold of a small number? Also anyone know how I source just two of the 1/2" UNC...
  15. M

    repairing late A airstack

    You could well be right about the lower step. When I've finished grinding the old weld it might be a different story there...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top