Recent content by Mark Schrier

  1. M

    Front Mount Distributor Components

    Having recently posted a thread on repairing damage to the front mount ditributor on my '49 8N, I was in search of all the usual parts to replace. My brother works at an O'Reilly store and I found a list of Standard Ignition part numbers. Points FD6769X Condenser FD71 Rotor...
  2. M

    Front Mount Distributor Repair on 1949 8N

    After looking at all the wear on the old piece that I have, I noticed other wear and tear that might create timing issues. When you add it all up, it probably explains why it wouldn't run perfectly smooth for the last several years. I went ahead and ordered one from Yesterday's Tractor. Just...
  3. M

    Front Mount Distributor Repair on 1949 8N

    I only ask because maybe someone else has order and tried one of these in an original disributor. My last experience was ordering a rebuild kit for a Marvin Schebler carburetor, only to find that one of the jets supplied was too tall and wouldn't allow the body parts to mate tightly. I was...
  4. M

    Front Mount Distributor Repair on 1949 8N

    Thanks! I only saw the complete distributor when I looked. Can anyone tell me how well this aftermarket shaft fits in an original distributor?
  5. M

    Front Mount Distributor Repair on 1949 8N

    This is a follow up to a thread I started back in September 2024. At first I was having trouble with the trctor back firing after it warmed up. After a while it would backfire as soon as I hit the starter. I finally looked at this problem again yesterday. I had been thinking it was a timing...
  6. M

    Backfiring and running rough after running about 15 minutes

    Wel, I did have a spare new coil and tried it but got the same results.
  7. M

    Backfiring and running rough after running about 15 minutes

    My '49 Ford 8N has developed an issue lately. I start it up and it's running OK. After running for about 15 miutes with a spring tooth cultivator, it will backfire loudly and then just barely keep running with no power at all. After sitting for an extended period and cooling completely down...
  8. M

    The Once a Year Figure Out How to Get It Started Saga

    Hey JMOR, You may be a braver man than me! I can see where this setup might work, just don't know if I have the cajones to attempt it. I don't remember seeing it anywhere in the manual. I am curious who was the first person to come up with it. :shock: :lol:
  9. M

    The Once a Year Figure Out How to Get It Started Saga

    Hey Tim, Thanks for the detailed method of diagnosing starting problems. It is a 6 volt system. I think my carburetor issues stem from moisture in the fuel tank. There is always a little rust in the bottom of the bowl after it sits for the winter. Fortunately, I still have a real...
  10. M

    The Once a Year Figure Out How to Get It Started Saga

    Hey duey, Yeah, I'm no good at electrical theory. So are there specific readings that would be found at the coil wire in each of the positions? I had only guessed that the resistor had lowered the voltage from 6.25 volts that I measured at the ignition switch to 3.25 volts at the wire...
  11. M

    The Once a Year Figure Out How to Get It Started Saga

    My 1949 8N seems to sit for about 6 months every winter. When I finally need to use it in the spring, there is always some issue or another that needs to be addressed before it will fire up. The carburetor is such a common problem that I almost automatically take it apart to clean it out...
  12. M

    Coil or maybe something else?

    I have had an issue with a '49 8N recently. I hadn't had it running since last fall. It took me a while to get it out again this summer. Turned out to be a dirty carburetor and got it running fine. Twice now, it has died on me and wouldn't restart. Both times were when I had the tractor...
  13. M

    Ford 9N ?

    Have to agree with the '49 8N theory. At least it looks a lot like mine. With the exception of the butchery that has occurred on this one. I'd say run, don't walk from this one!
  14. M

    Question for Admin

    Actually called Site Comments under the Support heading. Sheesh! Sure would be nice if the edit function worked. Maybe I should post a comment about that there as well. :lol:
  15. M

    Question for Admin

    Would this problem get better response if posted in Support Comments, down at the bottom of the Main Forum Index?
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top