(800) 853-2651
SHOP NOW

Recent content by MarkinMo2

Yesterday's Tractor Forums
  1. M

    Farmall 400 - is it worth anything??

    I like what someone said, offer 1,500. check to see if the TA works, replacement could be pricey 1000, 1500 in that area if you have someone do it. You don't really need one it should be just fine if its out on the lower side, but it is handy to have. IMHO
  2. M

    Farmall 450 Power Adjust Rear Rims

    Yes, standard IH wheel weights will fit the cast centers just fine Should have the 4 bolt holes in center casting
  3. M

    Holding value

    I agree with Wayne Lee
  4. M

    1086 Hydraulic lift question

    I've replace the pressure relief valve. Where is the pump located that operates the 3 pt. lift, and is it hard to get to?
  5. M

    1086 Hydraulic lift question

    Hey guys, I have a 1086. every thing works EXCAPT the 3 point. It has plenty of fluid and filter is good. Every thing else works good. My question is , where is the pump located for the 3 pt., Do I have to split tractor, and 3rd, can the average joe change it himself. I am pretty mechanically...
  6. M

    Frame weights

    Yes, they will. they fit the super series, super M, late model super H 300, 350, 400, 450
  7. M

    Parts for elwood MFWD

    I don't need any Now, hope I never do. Just in case is there a place where one could order any parts needed? Seems someone told me they are no longer in business, Thanks
  8. M

    Anyone else have International front wheel assist?

    Hello, I have an International 1486 FWA by ellwood. The drive shaft turns all the time, when it is engaged or not. Is this the way it is suppose to be or am I not engaging it properly? There is a small handle on the left front floorboard. Up is out, down engaged. I doesn't seem to move very...
  9. M

    New paint for the old girl

    It looks good for all you've done. It is your tractor, so, do as you wish. Paint it orange if you care. Looks good!
  10. M

    350gas 350 diesel. Fast hitch

    Does anyone know if a fast hitch from a 350 gas, will fit on a 350 diesel? Thank you in advance
  11. M

    400 fly cover plate, where can I find one

    There are 2 plates on the underside of my 400 gas tractor, the one I need is approx. 11" by 4 and 1/2 with just 4 bolt holes, it covers the fly wheel, but I don't think it is called the fly wheel cover, does any one know where I can pick one up? Or may be some one has one for sale, it just has...
  12. M

    400 hydraulics

    Does anyone know where I put the hydraulic fluid in my 400 gas, and about how much it holds? Thanks
  13. M

    I don't know what this part is.

    Open and close the radiator shutters
  14. M

    400 Wiring

    Any one have a wiring diagram for a 400 gas tractor? I"ve done something wrong, starts and runs good, but when I turn the key to shut it off, it just keeps on running. any help will be appreciated Thanks in advance.
  15. M

    Farmall C compression

    Does anyone know what the compression should be on a C Farmall, they check out to be 90, except one is 75, It just doesn't run right. I have rebuilt the carb, could the compression be the problem. It is hard starting too. Thanks for any info.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top