(800) 853-2651
SHOP NOW

Recent content by Marley

Yesterday's Tractor Forums
  1. M

    need help with Cockshutt 30 transmission assembly

    I"ll complete this thread by describing my ultimate repair. I decided to split the tractor instead of drilling and taping as I am not that good at it. You don"t have to separate the tractor that much. I took the lock nuts off the studs in the trans and put the nuts back on the first couple...
  2. M

    need help with Cockshutt 30 transmission assembly

    Mike, I did remove the creeper case cover to look inside. The creeper case has a hump where the end of the shaft is, basically it covers the end so you can"t get at it. Looks like the key is sandwiched between the two cases and to do it like they wanted at the factory, I"d have to split the...
  3. M

    need help with Cockshutt 30 transmission assembly

    Here is a pic of the key that I think goes on the end of the shaft somehow.
  4. M

    need help with Cockshutt 30 transmission assembly

    When I restored my Cockshutt 30 last year I screwed up. I split the creeper gear case from the transmission in order to install the live power take off shaft into the creeper gear box. (I converted a standard pto tractor to live power take off). Those parts went in fine. I bolted the creeper...
  5. M

    need a camshaft for F162 continental engine

    thanks for the info guys. I will follow that up. My cam broke, it was cast, and can"t be repaired. But now I"m hopeful I can get something to get my restoration going again.
  6. M

    need a camshaft for F162 continental engine

    I have a broken cam on my F162 continental engine. The people I have called for parts say it"s discontinued, or obsolete, so time to look for a salvage one I guess. Anybody have an old engine that they are parting out? My limited research tells me the F162 was used in Massey tractors 101 JR...
  7. M

    do I have to remove crankshaft gear to remove crank on F162

    Yes three eights inch bolt fits the crank gear holes.
  8. M

    do I have to remove crankshaft gear to remove crank on F162

    Just to complete this thread, I had a 2 jaw puller and took some 38 inch bolts and pulled the crank gear off the crank. Then removed 2 pieces, one being the washer with holes to align with pins in the block. The gear was not that tight, came easy with the puller. Thanks for the advice.
  9. M

    do I have to remove crankshaft gear to remove crank on F162

    Yes I got your email and replied. Thanks for all your help.
  10. M

    buttoning up my E3 project. need some assistance

    Re: your generator not charging, I think you'll be fine for the parade. I ran mine for 20 -30 minutes at a time without a charging generator when I first got mine going, and never had a problem. I expect on a fully charged battery, you could run the engine at one third throttle for a couple...
  11. M

    buttoning up my E3 project. need some assistance

    Re; the carb adjustment--- my 30 manual says the high speed jet (big one at end of carb) performs best at 1 to 1 and three eighths open. So I"d change that. The idle adjustment screw should work at 1.5 turns, I think mine is set at 1 turn. Re: timing---are you sure you have no. 1 cylinder on...
  12. M

    do I have to remove crankshaft gear to remove crank on F162

    Cockshutt 540 with the F162 continental engine. I have removed the connecting rods and the main bearing caps. I want to remove the crankshaft but when I lift it, something is holding it from coming up at the front of the engine. In the parts book I see some kind of thrust washer and pin in the...
  13. M

    E3 rear rims.

    Chris, I have both style rims you describe, the flat center style and the angle center style, both for the adjustable wheels. I"m 99 per cent sure the center piece of the wheel will fit both, but I will double check. Can"t do it today, will try and find time tomorrow.
  14. M

    E3 rear rims.

    Chris, the original rims on my 1948 CK 30 measure only 9 inches wide with the tires off, that is the inside measurement from bead lip to bead lip. I installed new 11.2 x 38 rear tires on them and they fit real nice. Actually, the rims had 12.4x38 tires on them and they fit nice too. The key...
  15. M

    Will Cockshutt 30 wheels fit a CK40 or CK570?

    I"ve got a pair of decent 38 inch rear tires on Cockshutt 30 rims, the kind with the steel wheel disc that bolts to rectangular pieces on the rims and allows many different tread widths, 9 hole centers, not the early 30 6 hole. Will the wheels swap onto a Cockshutt 40 or Cockshutt 570?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top