(800) 853-2651
SHOP NOW

Recent content by Martin Seebach

Yesterday's Tractor Forums
  1. M

    If same engines probably will. If engines are only a few years apart and same specs, probably...

    If same engines probably will. If engines are only a few years apart and same specs, probably will. Our loader/scraper JD 300 Industrial has same engine as swather, 1.8l 4 cylinder and I stole the fuel pump from baler (NH) with same mounting holes and mating shape as tractor, works fine. Living...
  2. M

    Literature---1961 Allis Chalmers "Head Start for '61 Farming" Brochure

    Cleaned up bought new in 1960 AC D12 and small offset disk then took it too Moms with disk and blade. Still have AC D15 spray rig with 2 booms, 4' under tractor body boom, 350 gal stainless tank behind seat and a magic wand for operator to use. Dad bought the D15 in late 80s. Our tractors now...
  3. M

    JD300 Industrial Loader Tractor Value and Questions

    Hi Jim, Thank you for the information. The 301A industrial is sitting in my front yard. I cleaned the screen you mentioned, and am now waiting on one of the other 3 owners to pick up fluid and drop it off in town or out here. Moved out to the ranch in 93 then had to spend a year in town for home...
  4. M

    Loader Help

    Have a 75 300 Industrial and your inlet side looks a lot like mine including the ball valve. Yes the upright can be part of hydraulic reservoir. Some models have a big nut on bottom of frame member heading towards front. Others you can drain most from the filter below feet area. On ours the...
  5. M

    JD300 Industrial Loader Tractor Value and Questions

    Hi, Fully realizing the post is 4 years old, did ya get the Deere John. Our 75 300 industrial loader with 3pt usually carrying gannon box scraper, scarifiers and occasionally an augur still running like a champ! Dad picked it up sometime in the 80s while I was doing IT consulting in Brussels or...
  6. M

    non hydroscope trans hydraulic fluid

    I checked under the gear shifter and other than working its way down the gear and/or hi-low shifter handle it seems water tight. I'm about to do the first hydraulic fluid R&R on JD 300 industrial loader/scraper. It was bought around 1988 and still fires right up, runs smooth and loses fluid from...
  7. M

    Tripping more

    Very well said.
  8. M

    Tripping more

    Coming up on 71 and when walking in a field, forest or my house I need to be aware of where my next footstep lands. If not, trip with bruises and the occasional blood will occur. 37 Chief, you made the right moves with the tractor on trailer, good to read that one ended well. While loading our...
  9. M

    Best way to clean out the Hydraulic/Tranny system on JD 300 Industrial

    Gear and range shifters can allow contaminants into the system? I'd looked into the cracked boot and didn't see any areas without a gasket. I'll double check manual. It is a 300 Industrial loader/scraper built in 1975 and we've had it since 88. Good machine but perhaps is one step lower in...
  10. M

    Best way to clean out the Hydraulic/Tranny system on JD 300 Industrial

    Is there a procedure write up for R&R JD 300 industrial loader/scraper hydraulic fluid?
  11. M

    Allis d12 anybody got one?

    I cleaned and made sure the AC D12 was working well. Took the tractor and an offset 3pt disc down to Moms home for yearly weed control. We also have a D15 custom built spray tractor. 2 side booms at 11' long can be lowered with independant shut off valves, middle section is fixed underneath and...
  12. M

    FTC suing John Deere

    And they raised with moving manufacturing and high corp functions to Mexico. Deere John...
  13. M

    John Deere 300 industrial hyd issues

    Haven't done it on ours and should. There is a procedure that adjusts delay time on shuttle. It gets moving in reverse within a second but take 3 or 4 seconds to move in forward. In front left of gear shifter is a threaded rod with a 1.5" long open ended nut fixed to lower shaft crossing drive...
  14. M

    John Deere 300 Industrial and a wade of JB weld

    It tends to stick itself if no ballast in rears.
  15. M

    John Deere 300 Industrial and a wade of JB weld

    Hi Dave, Ours has an 84" Gannon box scraper. 3 rams on it; A) angle from horizontal ram for cutting roadside drainage, B) Forward or reverse angle on rear grading blades and C) Scarifiers UP/DOWN (Had always thought them 'rippers') It was bought in 1988 and has been a solid, long lasting, easy...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top