(800) 853-2651
SHOP NOW

Recent content by masonvn

Yesterday's Tractor Forums
  1. M

    Wd 45 mounted corn picker.

    I’ll eventually get the serial number. I decided I’m going to go ahead and buy it. I’m gonna just buy another complete tractor to put the picker on if I can get it restored.
  2. M

    Wd 45 mounted corn picker.

    Am I correct that it’s a wd 45?
  3. M

    Wd 45 mounted corn picker.

    I have an opportunity to buy what I believe is a wd 45 with a 2 row mounted corn picker on it. The engine is missing and it’s been sitting outside for close to 30 years. I can get it for 150 bucks so regardless it’s worth a role of the dice to me just to try and restore the picker. I already...
  4. M

    Case 1370

    I have one I paid 5,500 dollars for. Its been perfect for me. I've had a little trouble with the a/c, but not too bad. I pull a 25ft keawanne disk and 12 row duetz 385 planter. The disk is hard on it, but it will get it done. I love mine.
  5. M

    2670 c2 clutch issue.

    So today, I pulled everything back apart. Everything looked to be just as it should. No bellville springs were out of place and all clutch disks and steel plates looked good. I didn't double check the timing marks coming apart. I was pretty confident the c3 was working fine, is it possible...
  6. M

    2670 c2 clutch issue.

    Just to update this a bit, I checked the pressure on the c2 tonight and I can get 175 psi and the tractor still will barley pull. What I did find to be odd was to get the pressure up that high, I had to pull up on the inching pedal. Otherwise, it stayed around 125. I'm guessing the pedal must...
  7. M

    2670 c2 clutch issue.

    i've been racking my brain on this subject, I paid close attention to the timing marks when putting it together. I am pretty confident the c3 is working right, so I think if the timing was off, neither of them would work. Perhaps someone that knows way more than me could correct me if I'm...
  8. M

    2670 c2 clutch issue.

    Thanks guys, I am for sure going to check the pressure. I do have the case shop manual. It's just been too cold here to fool with it as my shop isn't heated. I'll let you know what I come up with. As for the oil supply tube, I'd like to think there is no problems with it or the control valve...
  9. M

    2670 c2 clutch issue.

    I have not since putting the engine back in, it looked like new and I'm assuming it is still fine because it will pull fine in 2nd power shift. Its just reverse, 1st and 3rd that are weak which if I'm right all have the c2 clutch in common.
  10. M

    2670 c2 clutch issue.

    So I have been playing with my power shift some more. I've narrowed it down to something has to be wrong with the c2 clutch. I will check the pressure tomorrow, but my question is, is it possible for the clutch piston to be stuck in the carrier and not engage the clutches? I put in all used...
  11. M

    Re: 2670 powershift problem

    Help!!!! I got my engine back in this morning, fired it up and tried out the powershift. I’ve done something wrong, the pressure gauge on the dash is barely on the edge of the green from the yellow. It shifts in to reverse and 1,2,3 fine, but in 1 and reverse it barely pulls. Shift to 2 it...
  12. M

    Re: 2670 powershift problem

    Thanks, Rod. I was worried if this was a common occurrence or not. All the planet gears felt great in the one from the donor tractor so I didn't disassemble it and inspect them. I also notice when I removed the shaft of the gear that had no bearing in it, the split pin that holds the shaft in...
  13. M

    Re: 2670 powershift problem

    So just for giggles, I tore my planet carrier apart tonight. I had notice one of the planet gears didn't feel right. The needle bearing was completely gone from it, not even any remains of it inside the gear. A couple of the others look scuffed but all the needles were still in place. What...
  14. M

    Re: 2670 powershift problem

    I now have my power shift completely out and all the parts out of the donor tractor. Time to start heading back in with the good parts. Anyone have any advice on particular things to watch for that a first timer like myself may overlook??
  15. M

    Re: 2670 powershift problem

    I now have my power shift completely out and all the parts out of the donor tractor. Time to start heading back in with the good parts. Anyone have any advice on particular things to watch for that a first timer like myself may overlook??
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top