(800) 853-2651
SHOP NOW

Recent content by McGuyver

Yesterday's Tractor Forums
  1. M

    Hay crimper

    Thanks for all the replies. He is convinced he can make it work.they come up with some amazing things. I&j in pa i believe nakes a pto fire cart. Still do not kniw if it can build enough speed.
  2. M

    Hay crimper

    Central Ohio, my biggest question how wide are they? 8? would be nice. 5 & 6? is allot of passes on a field.
  3. M

    Hay crimper

    I am helping an Amish friend find an old hay crimper. He is old order & can not put an engine on it. So he wants to convert it to ground drive. How wide did they make the older crimpers? Would like an 8 footer, the biggest i found is 6. I cant find any info on specs. Any info would be appriciated.
  4. M

    3020

    Another hydraulic question. I have a 64 3020 & 148 loader. Would anyone recomend a close center joystick from under $250.00. Also hiw many gpm? I read that the 3020 puts out 6 gpm at the remote & 14 gpm total. So on a direct replumb would that be 14 gpm? Thanks in advance
  5. M

    3020/148 loader

    Do they make a close center joystick?
  6. M

    3020/148 loader

    TX Jim, serial # 57884, so that would make it a 64, what in particular makes the plumb job different? I believe the video I was watching was on a 68.
  7. M

    3020/148 loader

    Thanks to all! I am following the re-plumb video. I agree do it right. & add joystick.
  8. M

    3020/148 loader

    I have a 69 3020 & just picked up a nice 148 loader. Here is my dilema. The loader has 4 hydraulic hoses ( no joystick or controls. My tractor only has one remote. What do i need to do to get it working? Later down the road i would like to set it up with a joystick & free up my remote, but for...
  9. M

    Naa

    That was my first thought. I pulled the carb everything looked good . Hit it with some carb cleaner & put it back on. One thing i noticed is a gray gritty very fine sludge in the bottom of the sediment bowl. & the sed bowl screen was crusty. I wonder if the ethanol gas is hard or corrosive on...
  10. M

    Naa

    My 53 jubilee starts right off the bat. Then starts sputtering , missing, backfiring , barely runs fir about 20 minutes then BAM! It runs like a top non stop. We had a 2 n that used to act simular it had a small channel rusted out in the head gasket that was allowing some coolant to seep...
  11. M

    3020

    I have a 69 , 3020 powershift . Sometimes when it's below freezing I can't get it out of park ( when not plugged in) . I have to let it run & work the 3pt up & down until tranny heats up, then it's still difficult to get out of park. After warm up it is ok. Would there be frozen condensation...
  12. M

    starter

    Yep sounds like the ground. the brushes & all else inside is clean & shiny. When it"s not working no turn uver, no click, buzznothing. If contact is made it turns over & is running instantly. Yup. gettin real fast at removal
  13. M

    12v

    I did my conversion this weekend. Tractor ran great.I also rebuilt the distributor. I think most of my problems stemmed from worn dist shaft lobes (2N). They were not opening untill they got to the closing side of the lobe. New question? When I1st started it the ameter pegged to the left (-)...
  14. M

    coil

    In a 12v conversion kit Bought through YT how many ohms would the coil be? .7-1.5 or 2.5-3?
  15. M

    12 volt

    Thanks, much appriciated. I definately need reliable.Thanks all, & Dunk I bet those gennys are only sold in pairs right lol.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top