(800) 853-2651
SHOP NOW

Recent content by mechanic

Yesterday's Tractor Forums
  1. M

    175 MF lift issue

    Just curious if about the 3 point lift adjustment. Background on issue.. I was putting out round hay bails. After I set one out I raised the lift up. Took of across the field and hit a bump. The lift did the bounce thing and wouldn't go back down! I had this happen years ago and the hydraulic...
  2. M

    1970ish Ford 5100 rowcrop hydraulic

    Helping a friend who is restoring a 1970ish Ford 5100 rowcrop. He wants to know what the item in the picture is called?
  3. M

    Manuals

    thanks, I found my manuals!
  4. M

    Manuals

    Anyone have the manuals for a single stage clutch on a 1968 MF 175. Looking to adjust or replace. The clutch if need be.
  5. M

    Cav pump issues on a 1968 175 MF.

    yes
  6. M

    Cav pump issues on a 1968 175 MF.

    it's crazey, it worked fine till I had the dirty fuel.
  7. M

    Cav pump issues on a 1968 175 MF.

    it's crazey, it worked fine till I had the dirty fuel.
  8. M

    Cav pump issues on a 1968 175 MF.

    I didn't take the governor portion apart.
  9. M

    Cav pump issues on a 1968 175 MF.

    I had to clean my fuel system due to some kind of fuel contamination. Anyway, I had to clean out my CAV pump. I did a lite rebuild on it. Just the seals and such. I didn't take the internal portions apart at all. Took the top cover off and cleaned it out. Took the transfer pump filter...
  10. M

    Wedge tool MFN-163

  11. M

    Wedge tool MFN-163

    My manual says to installed this wedge tool. Too hold it in a neutral position. What exactly does that mean? Is it centered or just holds it fully extended? I suppose if I make this tool, it be obvious!
  12. M

    Wedge tool MFN-163

    Thanks! You know I'm struggling through this lift cover adjustment. I'm getting it though.
  13. M

    Wedge tool MFN-163

    Anyone have a picture or measurements to make this tool? I am in need of this for my 68 175 lift cover adjustment.
  14. M

    Massey 175 Lift cover assembly question

    I think mine is 68-69. I would like to do a full restore on it eventually. I have already done a complete teardown from rear main rope seal to the PTO seal and everything in between.
  15. M

    Massey 175 Lift cover assembly question

    So, I have a 175 also. I believe that a feeler gauge will work. My manual says that gap should be 0.170 +/-0.10.]
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top