(800) 853-2651
SHOP NOW

Recent content by mijohn

Yesterday's Tractor Forums
  1. M

    John Disc model H1200 trailer disc

    Its a KBA disk, I've got two of them. john
  2. M

    KBA Transport Harrow

    29 inches to the bend for over all length and with 4 inches of thread on the end. john
  3. M

    Literature---1960's NEW IDEA Hay Mower Brochures

    Still have a 254 with hydr. lift. that I use to clip pastures. john
  4. M

    To add to how things have changed

    My dad gave me the old car if I would stay on the farm when I was sixteen. A sedan, six cylinder, three on the tree. my friends were building V8 hot rods. I have a 1/2 ton pickup that rides and drives like a car. I would still go back and be sixteen again then be 78 now. john
  5. M

    KBA Transport Harrow

    I've got two KBA's so I'll measure them tomorrow and post it tomorrow night. john
  6. M

    JD plow? Size?

    I think its older then a 4B, because on a 4B the land wheel was at least 28-32 inches high. The furrow wheel was smaller. At least it was on the 4B we had when I was about fifteen when my dad bought a 44 to replace it. john
  7. M

    Used the b today

    nice spreader, N? , john
  8. M

    Another try on JD plow.

    In my plow book the cast bracket started 1n 1938 thur 1946. In 1946 they started with the flat bracket. After the war steel for the regular consumer became more open for industry. john
  9. M

    John Deere Row Binder

    That was my second job in the field, RIDING THE CORN BINDER TO TRIP THE BUNDLE CARRIER. I WAS FIVE OR SIX AT THE TIME. My next job was plowing with our John Deere M with one bottom mounted plow. My brother was plowing with our new to us, a John Deere A with a two bottom 2-14s model 44 plow...
  10. M

    720 Clutch slide grease

    Yes, the bearing the clutch pully rides on and the little toggles that operate the clutch. And I also grease the main bushing. you want to use high temperature grease. john
  11. M

    John Deere A Questions

    The single stick shift lever started in late 1950, the round holes in the cast wheels were brought out in 1951-1952 model years. you sometimes see earlier year tractors with that stile wheels but I think they might of switched from flat pressed steel wheel-rims for weight. the pressed steel...
  12. M

    Any vets here

    Jaden, were you and 05D. john
  13. M

    Any vets here

    USArmy 67-71 thank you all for your sacrifice
  14. M

    720 clutch bevel washers

    I completly overhaul all my two-cylinder clutches with new pins, bolts, toggles, dogs and whatever else is needed. And I always use Bellville washers after. The clutches are always less grabby and a lot smoother with them installed. john
  15. M

    JD 4 Bottom Plow ID

    Its an 810 because of the shot beam in front where the front courter bolts on. The 812 thur 814 has a longer beam. The 810 needed a shorter beam was needed because of the new three point hitch on the new 620-720 which the plow was built for. john
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top