(800) 853-2651
SHOP NOW

Recent content by mikeroche56

Yesterday's Tractor Forums
  1. M

    TO35 rear PTO shaft

    Thanks everyone, I installed a Speedi- sleeve and new seal. Leak is gone! Mike
  2. M

    TO35 rear PTO shaft

    :) Thanks, I have a sleeve and 2nd new oil seal on order. Mike
  3. M

    TO35 rear PTO shaft

    Thanks, good info.
  4. M

    TO35 rear PTO shaft

    Or asking a different way, has anyone had a leaky PTO shaft that wasn't fixed by only replacing the shaft oil seal and outer retainer Oring? If so, how'd you do it? Thanks!! Mike
  5. M

    TO35 rear PTO shaft

    Anybody used a Speedi Sleeve to repair the oil seal area on a TO35 rear PTO shaft?
  6. M

    TO35 Hydraulic lift troubleshooting

    Thanks everyone for the help. I got the new pump installed and it works great! Will make brush hogging a lot easier. I ended up removing the pump filter and control lever to make it easier to jockey around in the case and not worry about bending anything. Bad news is that I decided to replace...
  7. M

    TO35 Hydraulic lift troubleshooting

    Thanks, Bob. The pump width and the splines seem ok, i'll give it another go... Mike
  8. M

    TO35 Hydraulic lift troubleshooting

    Hey Bob I received my pump this week and tried to install it for a little while last night. Is there any trick to shoe-horning the new pump into an older to35? Do you need to install the collar with the cotter pin on the forward pump shaft before you slide it down in or should you install it...
  9. M

    To35 hydraulics

    Hi, I'm the guy Bob is referring to. It is my understanding the newer pumps with the filter directly replace the earlier ones. My pump and parts will be in this week, so should know for sure. I have a 1957 to35 and my sn starts with 173xxx. Only caveat is there was a period earlier than mine...
  10. M

    TO35 Hydraulic lift troubleshooting

    Good tips, thanks Bob!
  11. M

    TO35 Hydraulic lift troubleshooting

    Thanks for the help everyone. I ordered a pump. I'll report back how I make out. Mike
  12. M

    TO35 Hydraulic lift troubleshooting

    Oh, and my s/n is later 173xxx and i got the higher pressure relief valve.
  13. M

    TO35 Hydraulic lift troubleshooting

    Ok, Bob posted pics on how to chain down the arms. I can get about 1700 psi when revving up the engine and with things warmed up. If i drop down to a little faster than idle, the pressure drops to only 500psi. There is a lot of oil splashing in the inspection cover toward front of tractor...
  14. M

    TO35 Hydraulic lift troubleshooting

    Thanks! The pictures helped a lot! I'll try the chaining and report back. Mike
  15. M

    TO35 Hydraulic lift troubleshooting

    Steve, Thank you very much for the detailed post! With the guage in the test port and my 5' brush hog attached plus about 500 lbs added by me and my son the gage hit about 1700 psi. Wasnt sure how to chain the lift arms down. Note the tractor is relatively cold. I did see that once the arms...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top