(800) 853-2651
SHOP NOW

Recent content by Miller49G

Yesterday's Tractor Forums
  1. M

    Rod bearings .010 John Deere G

    Hello, I need to find a set of John Deere G rod bearings .010 under sized. I called up Restoration Supply but they are out of them and don"t know if they will get them in stock again. So were else can I find the .010 rod bearings at? My 49 G
  2. M

    John Deere G Transmission Question

    here it is. Gear Ratio Chart
  3. M

    John Deere G Transmission Question

    Go and look at my web site I have a complete gear ratio of a Styled G on there. Gear Ratio Chart
  4. M

    JD G

    Here"s a link to my restoration page of my 49G and my 37 USG. http://home.comcast.net/~miller49g/ My 49G
  5. M

    In need of .010 styled G rod bearings

    Here is were you can get them Restoration Supply. Here the web page http://www.external_link/john_deere_engine_g.html John Deere G Sn 14600 & up rod bearings .010 price $132.00 a set. My 1949G
  6. M

    F.I.T Comment Re: John Deere R Exploded Gov/Rack

    I you guys want to see something that i call restored then look at my web page. I did a full restoration on my John Deere G and i been at it for 2 years now I"m almost done with it. It takes alot of time and a bunch of money. My Restoration Page.
  7. M

    Triggering MSD with Pertronix

    The blue/green wire set on the MSD(magnetic trigger plug isn"t for hooking up the Pertronix. It is what you just said its a magnetic trigger pick up. If you hook it up to the magnetic trigger pick up it will not work and maybe fry the MSD box. Just hook it up like my link says. Its that easy...
  8. M

    Triggering MSD with Pertronix

    No resistor is needed on the Pertronix if you hook it up to a MSD box. All the Pertronix is a pick up (like a light switch on and off) it doesn"t jump up the power to the coil. The coil is what jumps up the power like say if you put a high out put coil in there.
  9. M

    Triggering MSD with Pertronix

    Glad I could help you out.
  10. M

    Triggering MSD with Pertronix

    Don"t hook the Pertronix (+) to the (+) of the coil. Hook it up with its own switched power. You will be getting the jumped up power out of the msd box when you hook it on the (+) side of the coil no good. I you hook it up like the picture on my web page it will work just fine!!! Any other way...
  11. M

    Triggering MSD with Pertronix

    Goto my web page and look on how to hook up a msd 6a box. PerTronix Wiring to MSD 6A
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top