(800) 853-2651
SHOP NOW

Recent content by Millwright

Yesterday's Tractor Forums
  1. M

    Leyland 270 clutch

    You need to use three clips that hold pressure plate compressed, then you have a two piece coupling for the drive and inside that is a pinned sliding coupling for PTO. I would suggest for you look for the Nuffield Tractor Forum from the UK, has links to manuals and video's. 270 Leyland is the...
  2. M

    Part 2 of Gehl Film Clips From 1955 In Color

    I know that direct cut head is a unicorn today, I have two FH 84's, a one row corn head equipped one has been here since new, and a pickup and select-a-cut feed transmission equipped one I bought at least twenty-five years ago, hoping to find a two row corn head and the direct cut head, as well...
  3. M

    1650 cockshutt filters and main engine clutch

    I missed the engine filter, use the Agco site for a part #, then cross to Baldwin or Fleetguard. Which province are you in? There are a few aftermarket sellers or Agco for clutch parts or filters.
  4. M

    1650 cockshutt filters and main engine clutch

    A Carquest can use the Bladwin # or Case-IH dealer can use Fleetguard #. Before serial# 147 569 crosses only to FG 3313(5.4" long/ 10 psi bypass), later serial# is FG 3311 or Baldwin B163(3.8 long/8 psi bypass). Run away from Fram or Wix filters.
  5. M

    Disk identification

    Kewanee for sure, I have the 44 plate version, the double taper bearing on the gangs was a bad idea!
  6. M

    Can you help me identify these parts?

    I'm not overly familiar with 4x4'https://www.novak-adapt.com/knowledge/transfer-cases/s, but based on the look of the case, I would lean towards a Dana/Spicer 18.
  7. M

    Baling In The Valley

    I've been over Sask four times going to and from Edmonton for turbine work, but I really need to visit. Great-grand mother was born and raised at Crescent Lake, Grandmother born in Saltcoats area, moved to Ontario in 1919 when Grandma was eight.
  8. M

    Wreck on Lakes

    It was also towing a fully laden barge that sunk,link is our local newspaper, another local long missing steamer (136 years), the Jane Miller was found in 2017. Untitled URL Link
  9. M

    HELP 10' kongskilde triple k

    Yes, nub is part of nut, the assembly will only come apart if you are able to turn the thread and move the channel up, most likely rusted/stuck.
  10. M

    HELP 10' kongskilde triple k

    They are not a through hole, they are a nub that protrudes from the square nut inside for the threaded adjustment, should turn and move up and down easy, if the crank doesn't turn you have a rusted and seized thread.
  11. M

    First year for FACTORY installed Farmall power steering

    I believe it would be around '53, on the Super 9's, maybe same time or later for the 6's using a cylinder on the drag link as an option.
  12. M

    Rear loader pump on 1365 Oliver for 1510 loader

    Shaft seals can fail do to age or heat, but in general pumps develop shaft leaks for two reasons, internal porting for the case drain is blocked, or rotor camber sides are scored up and the bypass is exceeding the capacity of the case drain. You will need to disassemble and inspect the pump to...
  13. M

    WD9 - Thermostat or no?

    No shutters? A WD9 with out a thermostat, should have shutters. Adjust opening relative to load and air temp.
  14. M

    Extra wide head machine screw

    You want flanged hex head or flanged button head depending upon the drive you require.
  15. M

    W 400 parts

    If you are looking for #'s 2 and 4, #2 is 60 763 DB up to ser# 3811, 365 456 R1 ser# 3812 up. #4 is 9 020 D to 3811 and 365 459 R1 from 3812
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top