(800) 853-2651
SHOP NOW

Recent content by modyinnh

Yesterday's Tractor Forums
  1. M

    NH 68 Hayliner banana bales

    Got it! Nice explanation, thanks. I baled the other day with no problems. I took into account the suggestions of heavier windrows and making sure the bulk of the hay entered the pickup closer to the bale chamber paul
  2. M

    NH 68 Hayliner banana bales

    Thanks for all the suggestions. Hopefully, I'm baling later today and I'll see how it goes. This same baler worked fine last year. The aluminum tines are, as you say, 13ish inches long and the steel ones with the spring on top seem to have the original red paint on them with no wear marks...
  3. M

    NH 68 Hayliner banana bales

    Hi all, We're having an issue on a NH 68 Hayliner where the feeder teeth (the steel ones; not the aluminum tines) don't reach far enough into the corner of the "pickup chamber" to grab the hay. This results in jamming of the pickup and, I,think, banana bale formation. I suppose we can live with...
  4. M

    keyed ignition switch??

    key to start
  5. M

    8N with 2N front wheels?

    Good suggestion!
  6. M

    8N with 2N front wheels?

    Thanks for the input p
  7. M

    8N with 2N front wheels?

    Also, I dont have any problems cutting and welding. Was just wondering if the rivets holes on the old one would interfere with the welding of the new one.
  8. M

    8N with 2N front wheels?

    I've been going on the assumption that its an 8N. Looked at John Smith's page: it has a 4 speed tranny, with a Huppe Dual drive; position control lever under the seat; has the newer, non-I beam radius rods; bothe brakes are on the right.
  9. M

    Hupp Dual-Drive

    Well thanks for all the replies. Now all I need to do is fix the clutch!
  10. M

    Hupp Dual-Drive

    Hi all, I've got a '48 8N (front mount)with a Hupp Dual-Drive aux. trans as identified from John Smith's page. I can go plenty fast without the use of the Hupp. My question is: under what circumstances (other than tractor drag racing) would someone use the Hupp? paul
  11. M

    Harbor Freight tire changer

    Nice. That's the one I was hoping you were referring to.
  12. M

    Harbor Freight tire changer

    would that be the $1800 or the $40 one? and thanks for the response btw.
  13. M

    Harbor Freight tire changer

    I always wondered how that HF tire changer was? Have you had it awhile?
  14. M

    Plow off of an 8n

    Well, I'm in Vermont so a moot point I guess. Hope it works out for you
  15. M

    Plow off of an 8n

    Where are you located? Wanna sell it?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top