(800) 853-2651
SHOP NOW

Recent content by MolineGB1997

Yesterday's Tractor Forums
  1. M

    Moline 403 engine value?

    Good morning. I have a 403 motor that I parted out from a gb parts tractor that I used for my gb restoration project. Just curious as to what the motor might be worth in a parted out state. Engine is bored to 4.75" and its all there minus heads and exhaust manifold.
  2. M

    Moline plow identification

    I haven't no. I'm not familiar with it.
  3. M

    Moline plow identification

    I see. So evidently I have an H model. I appreciate the help. I don't suppose theres anyone who makes replacement wear parts anymore?
  4. M

    Moline plow identification

    I was wondering if that may be the case. Though the hitch assembly looks different than the pictures I'm seeing of oliver plows.
  5. M

    Moline plow identification

    Any idea what model this plow might be?previous owner says it's an early 60s model. From the digging I could do, it seems it might be an H? Thanks for the help.
  6. M

    '55 GB Cylinder Boring

    Yeah I was wondering what it would cost to buy a jug and bore it vs sleeve the one I have. Is there a difference between the m5 or m670 intake/exhaust? I would like something compatible with the factory carb.
  7. M

    '55 GB Cylinder Boring

    Yeah I was wondering what it would cost to buy a jug and bore it vs sleeve the one I have. Is there a difference between the m5 or m670 intake/exhaust? I would like something compatible with the factory carb.
  8. M

    '55 GB Cylinder Boring

    Yeah I'm hoping there's enough material left to sleeve. I'm going to take the blocks and heads to Larsons machine in Fargo ND. I'm told they do good work.
  9. M

    '55 GB Cylinder Boring

    That's good to hear. Thanks for the advice!
  10. M

    '55 GB Cylinder Boring

    You mentioned the manifold off a 336 would work. Will that work with the original carb I have on my gb? And I've heard of the ub manifolds were restrictive on airflow. Is that the case with the newer type manifolds as well? Sorry for all the questions.
  11. M

    '55 GB Cylinder Boring

    Interesting that the one piece manifolds will work. Do they require a heat riser as well?
  12. M

    '55 GB Cylinder Boring

    I see. Thanks for the help. I'm assuming they don't make new manifolds because there are others that work.
  13. M

    '55 GB Cylinder Boring

    Glad to be here. Best place for info is from the folks who've done it. It's my first restoration so I'm learning a lot.
  14. M

    '55 GB Cylinder Boring

    Thanks for the reply. Information sometimes seems sparse on these tractors. Hopefully, I can salvage the cylinder blocks I have... Would be a shame not to use the like new pistons I have. Not sure what to do about an exhaust manifold yet. I'm hoping a manifold from another model will fit. I...
  15. M

    '55 GB Cylinder Boring

    Hey all and good evening. I recently picked up a GB gas as a restoration project. It's in generally good shape, but needs motorwork as it sat outside for the last few months. The front two cylinders are in good shape. The rear two not so much. The pistons seem ok but the cylinder block is...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top