(800) 853-2651
SHOP NOW

Recent content by molinepuller55

Yesterday's Tractor Forums
  1. M

    Moline U runs out of power when pulling.

    my brother jd plowboy had a u with the 09 heads on it. we were running it on 110 race fuel. before we changed to 10 heads, it would get around the 175ft mark and would die just like you turned the key off. pulled it 5500&6000, it would die same place on the track both hooks. came home put the 10...
  2. M

    Help

    36 tooth crank gear 72 tooth cam gear. Timing mark 180 degrees from 0 mark on cam gear.
  3. M

    Moline Reproduction Sheet Metal

    Aluminum hood, side shields, fenders, for U and UB Special would be nice.
  4. M

    A little trivia.

    $754
  5. M

    utu with solid head

    I also have a 47 utu, started out as the one piece head motor(kef)now has a 403 in it.
  6. M

    ub puller

    what did the intake manifold come off of? looks like an impco 200 carb on it.
  7. M

    mm heads

    looking for a pair of 28,29,or 33 heads
  8. M

    mm heads

    looking for a pair of 28,29,or 33 heads.
  9. M

    lightweight combine axle

    Looking for a lightweight combine axle to fit under a u moline puller. prefer a square tube axle. I have heard that an allis chamlers combine axle works well, but don't know what size. any help is appreciated.
  10. M

    combine axle

    looking for a steer axle from an allis chalmers combine. don"t know what size. looking to install under a pulling tractor. prefer square tube. my brother has one but didn"t know what size combine it came from. any pictures would be helpful. thanks, Brad
  11. M

    ub flywheel

    thanks guys for the replies. i think Jeff has what i am looking for. thanks again for the help.
  12. M

    ub flywheel

    i bought a tractor in pieces and it was missing the flywheel. it has a ub back half and a ub special front half. if you could send some pictures of it, i would greatly appreciate it.
  13. M

    ub flywheel

    looking for a flywheel for a ub. thanks for any replies.
  14. M

    UB project pics

    do you have any pictures of the u puller? would like to see hitch and wheelie bar pics. planning on changing my set up over the winter, and were looking for some different set up"s. you will have a slick looking ub when you get done. keep us posted.
  15. M

    18.4x38 tires

    looking for a set of 18.4x38 tires(preferable firestones)and 16x38 pressed steel rims,in or around SC. any info is appreciated.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top