(800) 853-2651
SHOP NOW

Recent content by Mr. Mayor

Yesterday's Tractor Forums
  1. M

    Genrator

    Would jumping bat to gen on the cutout before starting be a reasonable test of the pull-in voltage?
  2. M

    Igniton timing.

    Thanks Jim.
  3. M

    Piston rings

    My thoughts too but there was nothing with the kit as to the notch position.
  4. M

    Piston rings

    Not my first, but thanks! My last c-113 kit, about eight years ago, came with four ring pistons. Refresh my memory...... piston notch to the front...?
  5. M

    Piston rings

    I'm rebuilding a c-113 engine. The pistons I received with the kit are 3 ring, the originals were four ring and my IH and IT manuals both reference four rings. Any ideas on why this would be?
  6. M

    IH Distributor mystery

    You are correct, grease does indeed come out of the little hole. Thanks.
  7. M

    IH Distributor mystery

    The IH distributors have two plugs which per the operator manuals are supposed to be removed and replaced with zerks for greasing the drive unit and distributor shaft. In the last number of years I have worked on a SA, SC, SH, H and C. The distributors on all have had a long (2") bronze bushing...
  8. M

    C-113 Governor question

    Thanks Dave, I've done a number of these and always replace the springs, needle bearings and rockshaft bushing as well as the shaft itself. I am fortunate to have a full machine shop at my work and some pals that will make me what I need. I will check with my IH store as you suggested...
  9. M

    C-113 Governor question

    I?m rebuilding the governor from my ?49 C. It is missing the bumper pin that resides in a recess in the end of the governor assembly. The actuator spring is there but not the pin. I would like to make one but need to know the proper length. Does anyone have one apart that you could measure? I...
  10. M

    Touch control head gaskets

    The gasket and o ring kit for the 2 piston touch control unit comes with two thicknesses of head gasket. anyone know why??
  11. M

    Farmall C electrical

    Mine is a '49 too. It would be nice if the books covered all the options.
  12. M

    Farmall C electrical

    I have an early C with battery ignition and a generator with saddle mount cutout / four position light switch. I don't know whether the distibutor was added later, neither my parts or operators manuals shows this combination. Actually, the wiring diagram in the parts book shows a regulator with...
  13. P

    Farmall cub fast hitch crank adjustment mounting problems.

    A friend picked up a farmall cub with a fast hitch. The threaded part of front adjuster was bent and didn't work. We heated and straightened it out. He then went to reinstall and it doesn't bolt up any more. It's a long way from lining up as you can see in the first picture. Looks like the...
  14. M

    IH 350 question

    My buddie has a 350 Utility up on blocks for a tire change. He said that the wheels spin free even with the transmission in gear. Neither he nor I have any experience with TA"s. Is this related to the TA? The tractor functioned normally before he jacked it up.
  15. M

    Super C

    Farmall C"s with SC decals are common on ebay Take a look at the link. The cast iron upper steering support and brakes look like SC but the grill is definitely not, yet it seems to fit pretty well. Theories? Untitled URL Link
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top