(800) 853-2651
SHOP NOW

Recent content by mtb34

Yesterday's Tractor Forums
  1. M

    4020 Crankshaft Wear Sleeve - Front - Need Help Installing

    Thanks. I am using a ball joint press sleeve and some all thread. It lines up nicely with the new wear sleeve. It pressed on really easy until I got to the lip of the wear sleeve then it stopped and the crank turned. I can have someone hold the crank from turning while I try to press it on...
  2. M

    4020 Water Pump - Oil Cooler Line

    I got a new water pump for the 4020 and it looks like the tube that goes to the engine oil cooler just presses in. Should I just press it in with a vice and it friction fits or should I use some type of sealant on it? See pictures: Thanks
  3. M

    4020 Crankshaft Wear Sleeve - Front - Need Help Installing

    I pressed on the new wear sleeve on the crank today and there was a pretty definitive stop. It looks like it is not pressed on all the way compared to the old one I took off. I am not sure how I could press it on more unless the sleeve stretches as there is a lip on the inside that contacts...
  4. M

    4020 Crankshaft Pulley Removal

    Got the pulley bolt loosened today. I put the curved end of a tire iron against one of the hydraulic coupler screws and had my "assistant" put downward force on it while I loosened the bolt. It came out pretty easy. Not sure what the torque on it is. Will check my service manual. Hydraulic...
  5. M

    4020 Crankshaft Pulley Removal

    I need to replace the front seal on my 4020 diesel. Any tips on how to stop the crankshaft from turning so I can get the pulley bolt loosened? Also, for the hydraulic coupler screws that need to be removed for the puller, are they normal thread? I can fit a 1/4 drive in them but they aren't...
  6. M

    4020 Load Control Shaft Shimming Recommendations

    I forgot to mention that I replaced the front and rear drawbar bushings as well. I generally do that when I have replaced LC shaft components in the past since I have it drained and dropped. I ordered more shims and more seals. Will get it done again but have to wait until next year to test...
  7. M

    4020 fuel line from tank to pump

    Replace with a steel line ... you'll be happier. Give it multiple coats of paint. If you need a quick fix to get you by flexible is ok. I didn't think the tank was that bad to remove. Nothing up front was that bad. I took everything out and cleaned, tested, and painted...
  8. M

    4020 Load Control Shaft Shimming Recommendations

    Replaced 4020 LC shaft, seals, bushings (oversized) and used tractor all summer for mowing off drawbar - no 3 point arms - no leaks. All parts from JD. Did 1 week of work last week (20 hrs) with box blade and dirt scoop and now I have a leak. How tight should I have shimmed these...
  9. M

    3010 John Deere late 40s model.

    What kind of 3010 is this? I thought JD only built 3010 from 61-63?
  10. M

    320 skid steer hyd leak- ran then died

    That's good news! Thanks for updating.
  11. M

    320 skid steer hyd leak- ran then died

    What happened with the hydraulic leak and the hydr sight glass with no fluid and the locked up hydraulics? Was this all really a diesel leak that you imagined was hydraulic fluid?
  12. M

    1965 4020 PS three point

    Cam follower will have have some play along but not sure why you are focused on load control selector per se. Are you 100% sure the linkage is fully actuating from the console lever back to the valve operating lever? I am guilty of thinking I had the cable tightened in the console only to...
  13. M

    320 skid steer hyd leak- ran then died

    guessing main hydr pump - not alot if info to go on $6k mostly labor $3k for reman pump - rebuild yourself for $800 ... depending on what is wrong with it let us know what you find
  14. M

    1965 4020 PS three point

    Sounds like you are having load control selector linkage issues. There is another person right now having the same issues that has a post going with some nice pictures of what you and he are both dealing with. Check it out: https://forums.yesterdaystractors.com/viewtopic.php?t=1631215
  15. M

    John Deere 4010

    On second look maybe those are just install marks on lock plate from hammer or chisel ... still check clearance it is close to ring. Also have tou checked/adjusted linkage under right cover?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top