(800) 853-2651
SHOP NOW

Recent content by Mtnfarmer

Yesterday's Tractor Forums
  1. M

    1974 3000 loses hydraulic pump prime

    Just as title says Does not matter hot or cold every time you shut it off you have to prime the hydraulic pump. Pump is on the side of engine in front of clutch After you prime it it work all day until you turn it off. Not my tractor it is friends and he is getting frustrated with it. I...
  2. M

    Jd 4045-4038 engine

    Have JD 490 excavator with what I think is a 4039t in it it is a 1985 +or- a yr? It is getting oil into the radiator none in crankcase These engines where used in alot of Jd tractors also the engine oil cooler for these is part # RE 14448 super ceded by #RE31929 can any one tell me if...
  3. M

    TR 70 motor problem

    Not familiar with combines but if your resistor is a ceramic block looking thing engine should be a 391 Very common in industrial -truck and farm equip applications just replace it and you should be fine we go the same thing every year with two of our older ford silage trucks
  4. M

    Some Fox forage harvesters in WI

    I texted the guy about the 6200 open station that's a rare machine because most of them had cabs but this one came from factory as open station serial numbers say it was one of the first ones produced but it is his older uncles and they priced it at 7500. Too much for me auction market would...
  5. M

    Ford 8240

    So if I buy this tractor cheap enough the trans is a lost cause even if I want to rebuild it? Was hoping the clutch packs outta calibration -but worried that the 1-3-5-7 slipping in high range is beyond calibration. Tractor shifts fine just slips in these gears only under a heavy load (pulling...
  6. M

    Ford 8240

    Looking at a 8340 sle with 4quadrant powershift high range odd gears 1-3-5-7 slip when under load no load they are fine even gears 2-4-6-8 are fine. What's wrong with this tractor Clutch pack ? Calibration outta sink ? I know there are some guys on here that know about these appreciate any...
  7. M

    Neutral safety on 8240

    Where is the neutral safety switch located on a 92 model 8240 sle I'm having to wiggle the shuttle back and forth to get it to start :roll:
  8. M

    Ford 4610 Transmission fluid leaking

    Slip a wedge shaped block of wood in on top side of the front axle on each side tap them snug with a hammer this prevents the front half from pivoting on the axle , falling off jack , crushing you or the minimum of a cussing from you be mad at tractor and then realizing it was your mistake
  9. M

    Ford 5600 - things to look for when buying???

    I hope your purchase works out for you I also hope the 52 hp dyno was a typo error on your part 5600 should at least dynoed 65 hp 52 hp was what a 4600 had All ford when new would dynoe just a little more than advertised hp Where did they get the 540 rpm from dynoe readout or by...
  10. M

    New tractor

    I pickup and deliver for a mahindra dealer that is close to me The regen problem with kubotas are very real. I have seen it first hand mahindra has the best system of all and are good built tractors parts are no problem for us If you buy a mahindra make sure the dealer is knowlagable on...
  11. M

    NEW HOLLAND 848 BALER QUESTIONS

    That info I do not know without looking at actual chain in baler
  12. M

    NEW HOLLAND 848 BALER QUESTIONS

    848 is roughly 4x5 851 is 5x5 I think none of the 848 were sold to bale silage but they will do it with patientance. The light duty chain won't stand it very long though the heavier duty one will May have my early and late backwards in my previous post but the one with the heavier...
  13. M

    NEW HOLLAND 848 BALER QUESTIONS

    Early 848 had a light duty chain late ones had heavy or vice versus. Count the number of round bars the one with the higher number makes haylage without destroying the chain friend of mine has both think the one he uses for haylage has w wide pickup also he says it is the superior baler by far
  14. M

    717S DIRECT CUT HEAD

  15. M

    1959 Ford Gold Demonstrator value

    saw some ford gold demos on meccums tonight go for around 25000 if that helps If it were mine that's who I would see about selling it Better feild of collectors available than trying it alone
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top