(800) 853-2651
SHOP NOW

Recent content by MULE.

Yesterday's Tractor Forums
  1. M

    Kawasaki FB460V Motor questions.

    Thank you guys for your help. I'm going to start tearing that down and so I can check the valves. The rope is long and strong. Thank goodness if it ever breaks I'll go thru the side of the shed.
  2. M

    Kawasaki FB460V Motor questions.

    Thanks for the information. Problem is my wife who enjoys mowing, and would do so when I'm at work, can't start the thing. It pulls like a 45# compound bow. I was thinkg about putting a little starter on it, but I was concerned that the starter would turn it over.
  3. M

    Kawasaki FB460V Motor questions.

    Hey guys, I have a Gravely wing mower with the Kawasaki FB460V motor on it. It is a recoil start and always starts on the 2nd pull. Good thing that is does because it pulls very hard. I don't think the Automatic compression relief is working. I've owned and used this mower since 1990. I don't...
  4. M

    JOHN DEERE OLD PLATE WEIGHTS

    Wow, it's been one of those days Massey. Too many numbers. OK understand these weights will fit 4010's and 3010's, but my challenge is that we have 2 sets of weights which are for 34" or 38" wheels. They will fit on our 30" wheels, but I need a spacer to get them out beyond the lug nuts. Thus I...
  5. M

    JOHN DEERE OLD PLATE WEIGHTS

    Thank you Massey. I going to try to find some 3010S or 4010S and check the measurements across the center. Needs to measure 8 1/2" inside and around 9 1/2" on outside of the center hole lip to work with my current A3404R weights.
  6. M

    JOHN DEERE OLD PLATE WEIGHTS

    Will the R34810 wheel weights match to the A3404R weights as far as bolt holes and centers?
  7. M

    JOHN DEERE OLD PLATE WEIGHTS

    Did Deere make plate weights for old 4020's, with 30" wheels. I need a set with the center hole measuring 8 1/2" across. They must have the same centers as the 140#lb weights, part#(A34004R), which were for 34" & 38" wheels. The newer weights for 30" wheels have a 9 1/2" hole in the center...
  8. M

    JOHN DEERE REAR DISK WEIGHTS FOR 4020

    Thank you for your resonce. DElta Red and you are both making me think about a spacer. My first thought was to try and cut the lip off the cast iron weights but I think that would be real challenge to cut. The other option you guys made me think of was a spacer plate with holes drill in to match...
  9. M

    JOHN DEERE REAR DISK WEIGHTS FOR 4020

    DElta Red and Paul you are both making think about a spacer. My first thought was to try and cut the lip off the cast iron weights but I think that would be real challenge to cut. The other option you guys made me think of was a spacer plate with holes drill in to match the existing holes I use...
  10. M

    JOHN DEERE REAR DISK WEIGHTS FOR 4020

    Thank you Paul for your response. Problem is, the lip on the center of the smaller overal weight does not line up with the center of the overall large second weight. this prevents them from laying flat against each other.
  11. M

    JOHN DEERE REAR DISK WEIGHTS FOR 4020

    We have 4 flat old style 140# flat weights we took off a 3020 with 38" wheels. We want to use these on our 4020 with 30" wheels. As you know they will hit the lug nuts since the weights are 24" in diameter. But that is what we have and we need the weight on the 4020. So we thought if we buy 1...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top