(800) 853-2651
SHOP NOW

Recent content by my5sons

Yesterday's Tractor Forums
  1. M

    ih 300 utility power steering

    I just changed all hydraulic fluid and out of what would be the driver side of the tractor fluid started poring out. I removed the starter and there is the two bolts mounting ps to the tractor and in the middle there is a hole. The hole is where the fluid is pumping out. I don't see any threads...
  2. M

    Farmall 300 PTO drive gear

    Thanks for all your help. I haven't spent much time on these forums but yall have been a great help when I'm in a jam.
  3. M

    international 300 utility 56 teeth pto gear

    Thanks for your help.
  4. M

    Farmall 300 PTO drive gear

    So splitting the tractor it is. Won't be able to say "haven't done that before" after i get done with this. Is there anything I should change out or maintain while she's split.
  5. M

    Farmall 300 PTO drive gear

    Yes that retainer is on my tractor. What will loosening that do? I believe I have the clearance in between the two pto shafts where the seasonal disconnect is if I can just get the front spline to move up that 1/2" the gear will drop. But I'm not that lucky or am not seeing the answer. I hate to...
  6. M

    Farmall 300 PTO drive gear

    I have a 300 utility that the pto drive gear in the center of the tractor that runs off of the main drive shaft is missing about 4 teeth and wasn't even bolted in When I found out why pto didn't work. It looks like if I can get the pto spline to go a 1/2 " towards the rear of the tractor that...
  7. M

    Farmall 300 PTO drive gear

    This message is a reply to an archived post by T J Brewer on May 26, 2009 at 16:48:56. The original subject was "Farmall 300 PTO drive gear". my 300 utility's teeth look just like yours. How did you get it out? I'm haviny a heck of a time with this!
  8. M

    international 300 utility 56 teeth pto gear

    I have a international 300 utility that I just bought and it needs some work. The pto doesn't work do to the 56 toothed gear in the middle of the tractor missing teeth and not even having a bolt to hold the wheel on. I found a replacement gear but can't figure how to get the old one off!! Do I...
  9. M

    pto problem ih 300u

    Well I found the pto gears and plates. But the first large gear that makes pto spin is missing teeth and is wobbling around like its not bolted in. What is best way to replase this gear. I was able to push it back into place and make pto work but I'm afraid it will fall back out or hit the...
  10. M

    were is pto plate on ih 300 utility ?

    Well I just pulled covers off and the large fly wheel has big chuncks missing out of it and if it was suppose to have a bolt or screw it didn't. It was wobling loss and wasn't touching the small drive gear. When I wigled it in it locked in pto but I'm concerned about the missing teeth and...
  11. M

    were is pto plate on ih 300 utility ?

    There is three access plates. One is a T and one ie longer with what looks like a drain bolt and the other is a two bolt that appears to go to clutch and fly wheel. And will I need to drain any fluids from this area. The one long plate looks to be jerry rigged with lots of seal maker. Thanks in...
  12. M

    were is pto plate on ih 300 utility ?

    I just got a ih 300u ant the pto doesn't engage. I was told a sleeve pin probably came off . I haven't got a manual yet and can't wait to get busy.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top