-
Fird 4000 hydrauilic Resevoir
Where does this tube and banjo bolt go on this 4000 resevoir.. asking for my neighbor? -
"New" B-275
YOUR WELCOME... glad to help- nashranch
- Post #12
- Forum: Farmall, International & McCormick
-
"New" B-275
your injection pump is an inline pump. that control on side of it must be a primer. I would probably bypass it with the fuel lines to eliminate the leaking. This is a different pump than the one i had. I am putting up some of my setup. Mine smoked uncrontrollable so i removed pump and sent it...- nashranch
- Post #8
- Forum: Farmall, International & McCormick
-
-
International B 414
I posted to that link you sent- nashranch
- Post #13
- Forum: Farmall, International & McCormick
-
Ford 4000 steering cylinder
My neighbor brought over that second steering cylinder the other day and we took it apart and replaced those two little o rings in the middle section of the cylinder. He took it home and put the cylinder back on and he said it worked for about a minute. We put in similar o rings thinking that... -
International B 414
Run it hard and get it HOT to reduce condensation- nashranch
- Post #10
- Forum: Farmall, International & McCormick
-
International B 414
It's just condensation.. fill it with diesel/atf combo and run it around lightly and the drain it out and refill with correct oil- nashranch
- Post #8
- Forum: Farmall, International & McCormick
-
International B 414
Transmission and rear end. I've got more pics if you want any- nashranch
- Post #6
- Forum: Farmall, International & McCormick
-
International B 414
Yep i had one several years back... It was a beast. It had no power so i had Dieseltech rebuild the injection pump. After that it was good- nashranch
- Post #4
- Forum: Farmall, International & McCormick
-
Ford 4000 steering cylinder
Yep the seal popped right out with a pick -
-
Ford 4000 steering cylinder
My neighbor did get his money back on the leaky cylinder and i guess they don't want it back..Cool. So i get the pressure of rebuilding the original cylinder. I got it apart at the valve end ok. It just needs o rings in there. But the rod ends won't come apart.. got the or dust seal out and the... -
Ford 4000 steering cylinder
Thanks BarnCat. My neighbor did get another cylinder from Farmland tractor and it worked good but leaked from the get go. So know he's in touch with Farmland trying to get another one or his money back. Either way he needs to rebuild the one he has and I'll get the pleasure of doing that if w...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy