(800) 853-2651
SHOP NOW

Recent content by navyreteocs

Yesterday's Tractor Forums
  1. N

    MM Road Grader

    I know of a Chip Spreader on a U.
  2. N

    M5 Wide Front Problem

    I had a wide front M5 with a loader . would not steer or stop some was breaking at all time spent a lot of dollars still had a M5 . Found me a 4010 lp have had no problems feed hay or streening stopping ect . i know the where abouts of a round m5 front end in Kansas.
  3. N

    Removal of dozer from pond

    In my strip coal mining days we had a D9 stuck in a old pond hook 2 637 would not come 2 more 37s as these were push pull . look like a big shake but out it came . 1 more . Had a 637 stuck ran another 1 in hook on no come out started pushing with 2 more get 1 out back to the back in 2 rounds...
  4. N

    air in Tranny

    I have a 4010 standard (lp) with a 8 foward 2 rev. After bushing hogging I check the transmisson/Hdy. A great amount of air came out the dip stick Opening . is this normal? it there a vent thats pluged ? Thank you for your help Bernie
  5. N

    Air in transmission / Hdy

    I was bush hogging .after i quit i check the oiland the hdy . when i took out the Hdy Dip stick a lot of air came out . is there a vent thats pluged?? Thank you all in advance.
  6. N

    1924 John Deere Spoker D sells for $ 210,000 at aumann aucti

    Must of been 2 or 3 people with LOTS of money.
  7. N

    4010 LP won't start

    Take a hold of the butter fly the spring on the outside. hold it shut while turning it over to much air.
  8. N

    G1000 Vista diesel

    Whats a G1000 Vista (LP) Worth??/
  9. N

    Odd D Story

    When i was in the military at Port Hueneme ca. there were 2 huge warehouses will all kinds of equipment ready to deploy anywhere it was needed. they rotated this equipment every 5/8 years replaceing it with new this in the 60/70/80 .
  10. N

    D6c

    I ask before cant rember what was said . we have this D6 that quits pushing it will move very slowly . this happens about a hour you start pushing dirt after say 45 min its good for another 45 min to a hour of pushing . we thought the tranny (Power Shift)was getting hot install new temp gauge to...
  11. N

    John Deere A top speed question

    Some of MM red nose Us had a real big gear 38 miles per
  12. N

    D8 13a Caterpillar Bulldozer Pony trouble

    When I was younger about 60 years ago my father had 2 d7s i could start them with the crank because as the mec. said i pulled it slow and the mag likes it slow.
  13. N

    TX Jim 4010

    Tex i have a 4010 lp there a oil leak in front of the govener i replaced the gasket still leaks . how do you remome the flang that fit in the block TY.
  14. N

    4010 LP

    TY for your knowelge
  15. N

    4010 LP

    i Have a 4010 lp with a oil leak on the govener houseing How do you remove the flange from the block.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top