(800) 853-2651
SHOP NOW

Recent content by Nc995

Yesterday's Tractor Forums
  1. N

    Grapple problems

    This occurred to me also. When opening its retracting…and that’s where the bypass theory falls apart.
  2. N

    Grapple problems

    Me too. I had three of this same bucket at one time running on SVL90s and 95s. Operators put them through hell and still I’ve never seen anything like this.
  3. N

    Grapple problems

    Broke one clear off once and I’ve twice bent one enough to allow the o-ring to blow out and no longer be serviceable. I don’t get bent out of shape over busted fittings and hoses. It’s going to happen on occasion with grapple work. I do need to grapple to respond in the correct direction to...
  4. N

    Grapple problems

  5. N

    Grapple problems

    Thanks.
  6. N

    Grapple problems

    I’ve tried to isolate my inputs to one at a time. It’s difficult as old habits die hard (and grappling brush just work better with loader motions at your disposal). Best I can tell, it matters not whether I’m giving a separate input when closing the grapple. That I don’t know.
  7. N

    Grapple problems

    Either. I can run it at idle or at higher rpm, and it appears I can cycle the cylinders all day without a malfunction. 16-1700 is where I tend to run it. The grapple is snappy but not obnoxious at that rpm, and I still have enough oomph to run the loader.
  8. N

    Grapple problems

    It’s a land pride add-on; push buttons as opposed to manually operated valve.
  9. N

    Grapple problems

    What makes you think that?
  10. N

    Grapple problems

    It’s already quite jerky at anything above idle. I’m thinking it’s really going to need some restriction to cope with this setup. Anyway, add in that one side may be clamped on a load and that it happens when not expecting it, and I think that might explain my perception of very violent...
  11. N

    Grapple problems

    Thank you! I hadn’t seen intermittent bypassing like this before and it’s good to know it happens on occasion!
  12. N

    Grapple problems

    Jim - I have already stated that I have used this particular grapple. You seem more focused on finding fault in posts than anything
  13. N

    Grapple problems

    The point of saying “grapples” was that I have operated many of them and never seen this behavior. I’ve torn lines, rebuilt cylinders, and never seen anything like this. Usually a couple strokes and it’s in business. This one has been cycled hundreds of times and still has totally random...
  14. N

    Grapple problems

    I’ve used the grapple before on a different skid steers without issue, but it’s been a while. My reason in posting is this was thinking that perhaps there may be an issue with bleeding. That’s what it seems like to me. My thoughts are that the cylinders are small and with a short stroke, and...
  15. N

    Grapple problems

    I think you all have satisfactorily hammered home the point of not tearing apart a 3 day old fully warranteed tractor. The grapple is not from a dealer, not under warranty, and they aren’t going to troubleshoot or repair it.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top