(800) 853-2651
SHOP NOW

Recent content by NCWC

Yesterday's Tractor Forums
  1. N

    WHITE PINE TN

    Will the results be posted on the east tennessee site? At 1 am I didnt care where I placed but would kinda like to know now. Thanks
  2. N

    Crankshaft work?

    What is the going rate for a 6 cylinder crank stroked these days? Havent had any work done in years, tossing around the idea of another engine. anybody have any good shops close to the NC area? Thanks
  3. N

    Oliver 320 engine/S88 engine

    Well I have a super 88 engine that has been bored to far to be used. I got an email from a guy that told me he has a 320 engine and it is the super 99 gas engine. If that isn't correct then his information is incorrect. I know nothing about these engines so that's why I was asking.
  4. N

    Oliver 320 engine/S88 engine

    What are the internal differences in the 99 gas engine and the S88 engine. Will the S88 crank, cam, flywheel,and bellhousings interchange between these two engines?
  5. N

    E 3 GLEANER MOTOR

    Bought an entire combine for 300 in NC.
  6. N

    880 Oliver block

    Looking for a good usable block for an 880 or super 88 closer to NC the better. Thanks
  7. N

    880 super 88

    Where are you located at?
  8. N

    880 super 88

    Looking for an 880 or Super 88 engine. Closer to North Carolina the better. thanks
  9. N

    6 to 9 bolt wheel adaptors

    Brandon hit me up I can have a set made in a few days you can even pick them up.
  10. N

    allis steel rearend

    Man in my neck of the woods says the steel is heavier than the cast due to the bulky spindle casted peices
  11. N

    light weight puller

    I have an Allis Chalmers B with a D-15 engine very strong little tractor with 38 inch wheels for sale on craigslist in the charlotte area of NC
  12. N

    880 Oliver Parts Tractor

    I could use an engine out of an 880
  13. N

    Going rate for Crankshaft stroking?

    Ok.. Looking to have a 4.5 inch 4 cylinder crank stroked to 5.75 inch. Or a 4 inch 6 cylinder stroked to 5.50 inch.
  14. N

    Going rate for Crankshaft stroking?

    Been a few years since iv had a crank welded and went with a local guy the last time. Just curious to know what prices are everywhere else. Thanks
  15. N

    allis wd45

    The 262 will fit. If you have a diesel tractor to begin with it goes right in no problems if dont you have to move the radiator and grill out to the end of the frame like the diesels are and make a longer hood or find a diesel hood. As far as the governers im not sure enought to say for sure if...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top