-
N
Need help identifying this planter
Hopefully YT let's me load these photos.- Nicholasleu
- Post #1
- Forum: Implement Alley
-
N
Need help identifying this planter
I do have the bases for my fertilizer hopper. I actually have the hoppers complete hoppers they are just shot like most others you see. I do need a few parts like cast shutter the controls the flow for the amount of fertilizer that is dropped. Mine broke while I was trying to get it free. I will...- Nicholasleu
- Post #1
- Forum: Implement Alley
-
N
Need help identifying this planter
Hopefully it lets me upload- Nicholasleu
- Post #1
- Forum: Implement Alley
-
N
Need help identifying this planter
- Nicholasleu
- Post #1
- Forum: Implement Alley
-
N
Need help identifying this planter
- Nicholasleu
- Post #1
- Forum: Implement Alley
-
N
Need help identifying this planter
Good morning YT. So I have been working on my old planter what I though to be a mccormick/IH 251. After looking a little harder I see some sutle differences between mine and what is depicted in my manual. One being the depth adjusters. On mine there is a nut (maybe was swapped out) instead of a...- Nicholasleu
- Thread
- Replies: 6
- Forum: Implement Alley
-
N
MCCormick/Farmall 251 planter hopper base plate
Hey Kirk I thought I replied back sorry. I sent an email to you. Do you have any fertilizer hoppers?- Nicholasleu
- Post #1
- Forum: Implement Alley
-
N
MCCormick/Farmall 251 planter hopper base plate
Thanks for the reference to mike. I called he couldn't help out this go round. I gave him my name and number just in case he gets some stock in. Thanks again for the reccomendation.- Nicholasleu
- Post #1
- Forum: Implement Alley
-
N
MCCormick/Farmall 251 planter hopper base plate
leroy I am confused about your post. Are you stating that number goes to just the plate and not the entire bucket assembly or are you saying that I number is not the part number for the plate? That is the number stamped into the plate and when I go to Case/IH part finder that is the part number...- Nicholasleu
- Post #1
- Forum: Implement Alley
-
N
MCCormick/Farmall 251 planter hopper base plate
finally let me upload a picture of the base plate part number location.- Nicholasleu
- Post #1
- Forum: Implement Alley
-
N
MCCormick/Farmall 251 planter hopper base plate
Fossil, can you please check the part numbers of the base to be sure mine is on the plate itself. Here is a pic. Thank you for your response and fast response.- Nicholasleu
- Post #1
- Forum: Implement Alley
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy