(800) 853-2651
SHOP NOW

Recent content by nick kalisz

Yesterday's Tractor Forums
  1. N

    Stripped threads on P/S pump

    you may be able to buy aluminum welding rods. i've heard of these rods and you can melt them with a propane torch and just fill in the stripped hole , drill it out and tap it. http://aluminumrepair.com/land/index.asp?src=google&gclid=CODEvorEqq8CFe4DQAod8g0fXQ
  2. N

    simoniz pressure washer not working

    i have a pressure washer that didn't get much use it's a simoniz from canadian tire. the pump leaks like a siv and it has a honda motor.i phoned manufacturer and they say that they don't have any parts for the washer. does anyone have any experience or suggestions i'd like to keep the honda...
  3. N

    john deere model 420 phase 2 clutch replacement

    hi i believe i need to replace the clutch on a john deere 420 phase 2 . has any1 done this before? what parts would i need to buy and what would be the best way to install them...
  4. N

    Need Help Ford 3000 rebuild

    http://www.springfieldbiz.com/oaktree/rhcodes_serial.html
  5. N

    Rims

    350 for 2 FULL rims is not bad if its just mild surface rust on them see if he will go down to 300$ or 250$ from there sandblast and prime and paint the rims is most important for the life of the rims. i just got a jd 420 and we are fixing the rims because the previous owner did minimal maintanence
  6. N

    rad overflowing on jd 40 after using prestone stop leak

    hi my radiator is overflowing out of the overflow valve on my john deere 40 after using prestone stop leak. i know now not to use that stuff again because there is no water pump on those old tractors and it circulates naturally. but my question is what is the best way now to clean out this stuff...
  7. N

    finding new rims for john deere 420

    hi i'm trying to find new rims for a john deere 420 standard. i think i may have found them from a dealer 3 hours away but i want to make sure they are the right size i know they are 24" inches tall but on the tire it says 13.6 for the width now i haven't seen any rims on the internet that are...
  8. N

    finding part #'s for points on john deere 415-12 plow

    i'll keep that in mind i wish i had a spare to go on so i know what it's exactly supposed to look like the old one is tore up and rusted bad. i've been trying to find points plowshare and landside all around to keep the old plow in operation.
  9. N

    JD 40 S Cultivators

    i don't see why not as long as it has a 3 point hitch. should work fine jd 40 has a bit more power than the m as well
  10. N

    finding part #'s for points on john deere 415-12 plow

    hi im trying to find part #s for the landside points for jd 415-12 plow i may have a lead on finding parts for it @ http://www.crescentforge.com/
  11. N

    points for john deere 412-15 plow

    ya i just emailed you i think it's actually a 415-12'' plow part #'s bca 372 deere and i could barly make out through the rust on the other part 793
  12. N

    points for john deere 412-15 plow

    hi this is the first time i've posted on the forum. i'm trying to find points for john deere 412-15 plow i've looked everywhere for them but those of you that are familiar with the old plows parts can be hard to find because they are obsolete. any other ideas on where to find points? the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top