(800) 853-2651
SHOP NOW

Recent content by nicko-31

Yesterday's Tractor Forums
  1. N

    John Deere 503

    yes I did take it back. I will get it off the cutter tomorrow and try to get more info so I can make a better view of what to do.
  2. N

    John Deere 503

    Thank you for the replies, I currently have a wheel barrow set up on it but it goes flat due to thorns, also tried the solid type but rolled off the rim first time using it. It is a 12". So. I have installed with washer's to center it on the fork.
  3. N

    John Deere 503

    Yes, brackets are still there. I don't have any where near me that I can source a generic wheel. I'll have to check eBay which is always a chance. Usually doesn't go well.
  4. N

    John Deere 503

    My apologies, it is a Rotary Cutter also know as. (Bush Hog) it's only I believe a 5' wide that I use on my Ford 8-N.
  5. N

    John Deere 503

    Greeting's All, I have a old 503 John Deere that is in need of a tail wheel and No one has one and even if I could find it the cost is over $200.00. Has anyone any information on a replacement ?? Thank you in advance
  6. N

    8-N carburetor set up first run settings

    Thank you sir as well.
  7. N

    8-N carburetor set up first run settings

    Thank You very much kind sir. just what I was looking for.
  8. N

    8-N carburetor set up first run settings

    Greeting's all, can I get some rebuild first run setting for a Schriebel carburetor. There are I believe 3 screws to be adjusted but I don't know the starting point for them all. Kind Regards
  9. N

    1952 Ford 8N pto slipping out of engagement

    I wanted to follow up on my findings, after I pushed the bearing retaining sleeve up against the bearing it's self thus not leaving any play between the bearing, I reinstalled and tested. All was good. Not coming out of drive any longer. Thank you for your help.
  10. N

    1952 Ford 8N pto slipping out of engagement

    are you talking about the fork Richard ? Thanks
  11. N

    1952 Ford 8N pto slipping out of engagement

  12. N

    1952 Ford 8N pto slipping out of engagement

    What would be the price Bruce ? and a link Please
  13. N

    1952 Ford 8N pto slipping out of engagement

    . I removed the assembly and and the bearing looks good. The sleeves in front and behind the bearing on the drive shaft are giving me a reason to question due to the gap between the housing with the bearing. It is at least 1/4 of an inch of play between the two sleeves. Any thoughts ? I would...
  14. N

    1952 Ford 8N pto slipping out of engagement

    I will look into that. Thank you. Any post on replacement for the bearing. ?
  15. N

    1952 Ford 8N pto slipping out of engagement

    Greetings all, as of late my 52-8N has been slipping out of PTP engagement while using the Bush Hog only. It does not disengage on it's own while using other attachment's such as disc, rake Etc. any suggestions as too look at ? Regards
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top