-
N
Fuel issue I think?
Update: I noticed the fuel coming from the tank is reduced I tried to blow air through the lines to unclog it assumeingbthat it is clogged with no positive results I am assuming that?s where my problem is -
N
Fuel issue I think?
That?s what I was thinking with the float il be checking it today or tomorrow -
N
Fuel issue I think?
That?s what I was thinking with the float il be checking it today or tomorrow -
N
Fuel issue I think?
I have great spark no issues there I can throttle down a clutch when it does it and allow fuel to build back up and it will run a while before I put a load on it again I can make it do it so I know it?s fuel related -
N
Fuel issue I think?
I have good flow from tank through screens and carb float bowl fills fast everything appeared to be good but I can always double check In the event that all that checks out again where should I look next -
N
Fuel issue I think?
Ok I have a 64 4000 gas Starts and runs perfect all day everyday except When I go to (proofmeter reading) pulley 1316 rpm If I run there say speeding up bush hog or going down the road it acts like I?m running out of fuel and may even die if I sit there about a min it will start up no issue... -
N
64 ford 4000 help please
Here's where I'm at Under compression check I got 124.5 125 124.5 125 Went ahead and Replaced head gasket for grins (it can in a kit I bought) Adj valve lash Replaced intake exhaust manifold and gaskets New wire harness is on the way Replaced thermostat and gasket And new plugs Still not...- Noahsswan
- Post #1
- Forum: Restoration Processes
-
N
64 ford 4000 help please
That sounds very interesting Was it the same machine- Noahsswan
- Post #1
- Forum: Restoration Processes
-
N
64 ford 4000 help please
that was my last option to what may be wrong after thinking there is a short heavy duty looking spring that is connected to the hand throttle and not sure where other end goes i wanna say with the research i have done it may possibly be the gov spring but i don't think that will cause the...- Noahsswan
- Post #1
- Forum: Restoration Processes
-
N
64 ford 4000 help please
And I was off on the year it's a 1963 Do these have a timing chain or are they gear to gear And what would the chance of it "jumping a tooth"- Noahsswan
- Post #1
- Forum: Restoration Processes
-
N
64 ford 4000 help please
It will run it just has to be advanced far- Noahsswan
- Post #1
- Forum: Restoration Processes
-
N
64 ford 4000 help please
The old one yes The new one it all tight no movement and spring clip is there The excessive play is why we changed it- Noahsswan
- Post #1
- Forum: Restoration Processes
-
N
64 ford 4000 help please
Thanks for the welcome As far as checking for leak we have sprayed to check for leaks With no change as far as seeing if the throttle plate is backwards I have not I will check that the first second I get Thank you for the input- Noahsswan
- Post #1
- Forum: Restoration Processes
-
N
64 ford 4000 help please
We are having issues with a 64 ford 4000 I will try to be as complete as I can My dad has a 1964 ford 4000 gas 4 cyl and as he was bush hogging with it it just died on him he said it was like some one shut the key off the and would not start back up After playing with it a lot this is...- Noahsswan
- Thread
- Replies: 14
- Forum: Restoration Processes
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy