(800) 853-2651
SHOP NOW

Recent content by Noforddon

Yesterday's Tractor Forums
  1. N

    Maximum dyno hp thru pto on JDG

    Blink It!! 1 3/4" is the flipping large shaft you would want for a G. I need a F649R going by serial number? Any body know of one???
  2. N

    Maximum dyno hp thru pto on JDG

    Who's got a pto shaft for a later model G? I thought I had figured out through JD parts that a A and a 60 used the same one. So I found one.....NOT, to small. It's 1 3/8" diameter but to small where it splines into the G spider gears. Any body have one?
  3. N

    John Deere Duplex to Single Barrel Manifold Adaptor

    This is a spacer adapter to connect the duplex to the single barrel Jerrys manifold I already have. It would be something cheaper than the $480 Murpheys duplex manifold. Any body heard of such a thing??
  4. N

    John Deere Duplex to Single Barrel Manifold Adaptor

    I was told today some one makes a adaptor to bolt a JD duplex carb. to a single barrel manifold on a G JD. Any body know anything about this??
  5. N

    Elkton, Ky Sled

    OMG, Does he have the mental capacity to do math ?! ;-) And his old rust bucket farmal is goning to win every hook now!
  6. N

    Elkton, Ky Sled

    Who is the new owner?
  7. N

    Air Flow Through Big CI G JD

    Lower RPMs in the 1200 to 1300 range. Seems like I feel uncomfortable vibration over that.
  8. N

    Air Flow Through Big CI G JD

    Thanks Josh. Is there improvements in air flow that can be made to that Jerry"s head that will add even more with the duplex carb.? And also I have a duplex carb. off of a 50 JD that I have bored straight though (it has no ventures) and drilled out the jets that I used on a smaller tractor. Will...
  9. N

    Air Flow Through Big CI G JD

    I have a 815 CI G with a Jerry's block and head. It has a single barrel big nut carb. and cam from Denny's. Probably built several years ago a little while before Murphy's acquired Jerry's. Will a duplex carb. set up gain enough HP to justify the expense? Is the air flow through the head a...
  10. N

    JD G Clutch

    OK, thanks.
  11. N

    JD G Clutch

    Is there such a thing as metallic button clutch disks for a big cubic inch G? Or something that will hold more than the stock clutch disks?
  12. N

    Wheel spacers for 9 bolt wheels

    Sent you an email 6pack, thanks.
  13. N

    Wheel spacers for 9 bolt wheels

    Does anyone make a aluminum wheel spacers for 9 bolt hubs? This would be a spacer to move your tires and wheels out away from the tractor, a little bit, like you would need with a weld on hub.
  14. N

    18.4x38 tires

    I think I have found some wheels and tires close to home. Thanks for all replies.
  15. N

    18.4x38 tires

    What does gum dipped mean? And how much do you want for them?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top