(800) 853-2651
SHOP NOW

Recent content by north puller

Yesterday's Tractor Forums
  1. N

    trying to understand the rules

    Most pulls will measure the weight of the tractor with the driver. If you weigh 6300 lb with you on the seat, then you can only enter a class with a weight limit of 6300 lb or higher. Most likely you would start is a 6500 lb class. Some pulls will allow a grace at the scales. You could pull...
  2. N

    450 lp head

    If you want to add Murphy's rockers, you need to clearence the head in the push rod gallery's. Otherwise they will rub.
  3. N

    red diamond 450

    New project?
  4. N

    Feversham spring pull

    See you Sunday.
  5. N

    Feversham truck and tractor pull

    Countdown is on!
  6. N

    Driver skill and tractor pulling

    The tractor itself is a major part of the equation. I could put a beginner puller on a good tractor, and he will do good. I could put an expert driver on a poor tractor, and he will do poor. You could put the best driver behind the wheel of a Honda Civic, but he's not gonna win any NASCAR...
  7. N

    Feversham spring pull

    The Feversham Agricultural Society will be hosting our second annual spring truck and tractor pull on Sunday, June 12, 2016 at the Osprey community center and arena. Tractor registration will open at 9:30AM, and the pull will begin at 10:30AM. Pulling order will be light to heavy. Pickups will...
  8. N

    Farmall M Ignition timing for stock class puller

    A dyno is the best way. If you can't get access to a dyno, then use the 22 deg number. Run the tractor up to 1850 or 1900 rpm. Make sure the distributor has fully advanced to the stops. Set timing at 22 deg BTDC with a timing light. Lock it down. Reset governor to 1750 rpm.
  9. N

    Feversham truck and tractor pull

    Feversham Agricultural Society's spring truck and tractor pull will be on Sunday June 12 2016 at the Osprey community centre Feversham Ontario. Truck classes will be 6500 street gas, 8500 street diesel, and open diesel. Tractor classes will be 3500, 4500, 5500, 6500, 7500, 8500, 9500...
  10. N

    Feversham spring pull

    Osprey Community Center Feversham, Ontario, Canada 20 min south of Blue Mountain
  11. N

    Feversham spring pull

    Feversham fair spring truck and tractor pull will be Sunday June 12, 2016. Stay tuned for details.
  12. N

    39 Farmall M rearend as weight loss option

    Cap bros 9 bolt hubs will save you 100lb
  13. N

    Allis c hubs on farmall c

    Just stick em on. They both use the same bearings. They will seem stiff to turn because the felt dust seals are a tight fit.
  14. N

    Tractor pulling sled for sale

    Got it. See it on FB too.
  15. N

    Tractor pulling sled for sale

    My email is open. Send me an email and I will send you back my number.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top