(800) 853-2651
SHOP NOW

Recent content by Okie Haymaker

Yesterday's Tractor Forums
  1. O

    1950 Farmall C replacing transmission

    yes I do.
  2. O

    1950 Farmall C replacing transmission

    I'm getting ready to replace the transmission on my 1950 C Farmall as the housing has a crack in the housing on the side that my uncle tried to braze and it didn't work and it leaks gear oil. I have another complete transmission that I was going to swap out. My question is - Has anyone ever...
  3. O

    4430 over heating

    I won't venture to guess what is wrong with your tractor but I'll tell you what worked for me. I did just about everything talked about here. I took an air compressor to the field to blow the dust out of my 4230 at least 3 times a day, eventually I bought a complete new radiator, replaced fan...
  4. O
    Expired

    Wanted John Deere transmission breather cap

    I need a transmission oil breather and fill cap for my 4230 John Deere tractor. Factory part number was AR55304. That number has been discontinued and replaced by AL2137T which is discontinued also. Mine is the early style push on cap. Most of the early 30 series tractors used the same cap...
  5. O

    MF 135 12v generator to 1 wire alternator conversion

    Well, I struck out at the alternator shop. Probably 90%+ of their alternators and starters were for automobiles and very little tractor stuff. They had a few Delco 1 wire alternators and even less of the mini's modified to 1 wire. He told me the 1 wire mini alternators don't last very well out...
  6. O

    1970 AC 190xt series 3 power director pressures

    I got my parts Wednesday and finished baling Thursday and brought my tractor and baler home. This afternoon I replaced the spring in the relief valve port and doubled up with 2 flange bushings as Skyhighballoon mentioned above. Now I'm getting between 270 and 280 pounds pressure on both High...
  7. O

    MF 135 12v generator to 1 wire alternator conversion

    I did some looking around the internet last night and the mini alternators I found were made in China. I won't say all but most but what concerned me more was the fact that they were so open and not so weather or moisture proof. I found a 45 amp alternator like jt501 was talking about but the...
  8. O

    MF 135 12v generator to 1 wire alternator conversion

    I have a MF 135 with the perkins diesel and a 12v generator. I have replaced the voltage regulator several times and it will work for a few months and quit. I had the generator tested and it's still good, just not putting out much amperage. Even a new only puts out about 11 amps. I tried a Delco...
  9. O

    1970 AC 190xt series 3 power director pressures

    Thanks, I'm reading this a 10:00pm and the tractor is a mile north in the hay field but I'll check tomorrow. I've already pushed around on the linkage some and the only thing loose I found so far is the little bearing block part # 243049 on the horizontal linkage shaft below the platform fits...
  10. O

    1970 AC 190xt series 3 power director pressures

    Here's a pic of the actuating valve and where I connected my gauges.
  11. O

    1970 AC 190xt series 3 power director pressures

    No hydraulic clutch. The service manual says the relief valve is supposed to be set at 220 PSI if I checked it in the right place. I live about 75 miles south of the Kansas border and Mt Hope is about that far on farther north. I didn't want to take my old truck out of Oklahoma. If I'd get...
  12. O

    1970 AC 190xt series 3 power director pressures

    The power director on my AC 190xt was slipping a little bit in high range so I figured it was time to replace the power director clutches. The nearest dealer around that was familiar with the old Allis tractors was about 150 miles to the north in Mt Hope, Kansas and said it would be close to...
  13. O

    D Case Restoration

    I appreciate you taking the time to answer what probably seems like trivial questions but I have learned a lot from your answers. When I get a little farther along I'll try to post some pictures. Thanks for your help.
  14. O

    D Case Restoration

    Will the rust converter work as a primer or do I need to use a primer over the rust converter?
  15. O

    D Case Restoration

    Thank you Gentlemen. I have picked up a lot from your replies. The front wheels look good from the outside so I may not do much to them. The back rims you've talked me into going ahead and breaking them down and checking them out. I've got a small sand blaster but a sander and wire wheel would...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top