-
OldFart187 replied to the thread Crazy Distributor.Thanks. Actually i did set the static timing with a thin piece of paper, same as shown in your picture. That will get it started so i... -
OldFart187 replied to the thread Crazy Distributor.Wasn't the first time or the last. I did learn a lot so it wasn't all wasted.
-
OldFart187 replied to the thread Crazy Distributor.Found the real problem: me. My neighbor came over and straightened me out. I was setting it up based on the distributor rotor rotating...
-
OldFart187 replied to the thread Crazy Distributor.Good thought about the dust cover. Another possibility. The cap I have looks new, likely replaced just before I got it.
-
OldFart187 replied to the thread Crazy Distributor.SOLVED! I think. Although you frequently can't trust AI, two of them said the existing cap is the wrong one. The cap I have has the...
-
-
OldFart187 replied to the thread Crazy Distributor.Thanks. I'll check it out.
-
OldFart187 replied to the thread Crazy Distributor.Same set that worked just before it was removed.
-
OldFart187 replied to the thread Crazy Distributor.Makes sense, not idiotic at all. I've been known to overlook the obvious so I appreciate any cross checks. The crankshaft rotates...
-
OldFart187 replied to the thread Crazy Distributor.It was pointed to the #1 plug to put shortest wire in that general direction, really not too important since you can switch wires as...
-
On my Ferguson TO30, likely similar to 9N, 8N and many others, I removed the Delco distributor after the tractor was running ok. On...
-
-
On my Ferguson TO30, likely similar to 9N, 8N and many others, I removed the Delco distributor after the tractor was running ok. On...
-
-
Just reassembled the pump, top cover and quadrant after disassembly, cleaning and new valve. With the dipstick cover off but before the...
-
-
This starter is in good condition and works well. I'm replacing it with a 12v starter as part of a 12v conversion. It's a JST...
-
-
OldFart187 replied to the thread Sheared Flywheel Ring Gear Locating Flange.Running the 6v starter on 12v produces 4x the pinion impact force and torque. No wonder ring gears get knocked back. Resistors that...
-
OldFart187 replied to the thread TO30 Brake Assembly Procedure.Yes I have a manual. Six in fact: Owners, Shop and Parts in hard copy and on my iPad. No excuses. The bracket on the radius arm is...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy