(800) 853-2651
SHOP NOW

Recent content by OriginalRWT

Yesterday's Tractor Forums
  1. G

    grain bagging scale

    I would to purchase a used open mouth bag filling scale to fill 50# bags with, have tried but can't find any used listings could some point me in the right direction?
  2. K

    MF50 Mineral Gear Oil Question

    I have a 58 MF50 with a FEL. The rams started leaking so I took them somewhere to have new seals put on (I couldn't find any info on the Rams to find replacement seals. The lines have quick disconnects. Anyways, I got them back and it looks like there is some fluid in them (fluid comes out...
  3. P

    1850 diesel orbital power steering motor

    I have had a leak up the steering shaft for a while now and the top needle bearing fell apart about a year ago- I figured as long as it steers fine just run it... Well now it does not! I can steer it if I push down on the steering wheel with about 20 or 30# of pressure but when you let go the...
  4. C

    Bad coil on a 184

    This is the first time in all my years of running old tractors I had a coil go bad. It was on my 184 Cub. Last time I mowed with it starting running rough and got worse the further I went. Almost couldn't finish the yard. Today I got around to some trouble shooting. After checking timing, the...
  5. J

    Help! 3 cyl 820D was Florenced revisited

    Well, they got it running but said the transmission shifts "hard" and the brakes don't work. It actually flooded up to about mid-engine. Don't know if the alternator was ruined or not. Hopefully the trans will smooth up. They changed the fluid twice with a new filter the second time. What...
  6. 2

    Jeremy Regarding Air Ride Seat

    Hi Jeremy, here is a picture of the parts I was looking at to either isolate an air ride seat and/or the Rops in that 4320 cab. With some thought I believe you could do both with one design. On the Generation II and newer the cabs are mounted on theses isolators and the seat is mounted to...
  7. H

    Model A starter reinstall

    Can someone out there please tell me the easiest way to reinstall the starter on my 51 Model A? It was pulled out and rebuilt by someone else and now I want to put it back in. Huge problem from what I see! There isn't enough room inside the frame to install it without having the cables attached...
  8. D

    Allis Chalmers Decals

    Can anyone tell me what determines whether a D15 Series II would have plain cream decals or decals with chrome on them for the hood? Thanks
  9. 0

    Oliver 1955 fuel return line leaks

    Oliver 1955 return lines leak around the rubber "roosa master T's". Does anyone know where I can buy these?
  10. C

    DLTX3 load nozzle loose in bore

    Thoroughly cleaned carb - removed nozle using #8 screw and nut as a puller -came out easy - nozzle was dirty and had a ring of crud at the bottom I wire wheeled the nozzle and the crud flew off -the nozzle is in great condition I cleaned the bore of the carb -there is a step/ring cast into the...
  11. R

    620 all fuel vs gas

    I'm a novice on 2 cylinders how do I tell an all fuel from a gas
  12. K

    1326 cutter

    Would like some info... just bought an older JD 1326 cutter/conditioner.. The apron underneath is missing, with only the adjusting rod left.. My thoughts are to replace it with heavy tarp material and a oak 1x4 to connect to the adjuster..Will that work ok? Any other info on the machine will be...
  13. O

    580 Super D backhoe

    Help needed - I have a friend with a 580 Super D Backhoe. His trans went bad and cracked the housing when it let go. It is used on his farm mostly - he is looking for a transmission (hopefully the correct one,not a "close fit")at a reasonable cost. Any Ideas I have looked quite a bit for him...
  14. O

    2150 Hydraulic leak

    I had an 1800 leak when all of the old gasket didn't get scraped off. It was in front of the pump mounting stud and I had to use a mirror to really see it. No, I didn't do the original scraping. RT
  15. O

    Hi Speed Shift Into Reverse

    My experience was a 68 plymouth with a 318 and a 904. It was bumped into reverse for about a second. Tires squalled on the concrete highway but it didn't kill it. I don't remember exactly how long but I would say a few months later it wouldn't back up. The rear band (low-reverse I believe) was...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top