(800) 853-2651
SHOP NOW

Recent content by OzMF35

Yesterday's Tractor Forums
  1. O

    Diesel Surging Issue minimec pump

    Thanks guys, I'll go back over the lines looking for leaks and try the other suggestions and hopefully it comes good. Otherwise it might be off to the injector pump specialist.
  2. O

    Diesel Surging Issue minimec pump

    I've been over the fuel lines a few times and don't believe there's any leaks or restrictions, but will check again. The surging starts as soon as it fires up and there is no load on the engine. Doesn't seem to matter at what rpm? Here is a video I took if its helps anyone...
  3. O

    Diesel Surging Issue minimec pump

    I've got an old Ford 2712e 4 cylinder diesel engine on an irrigation pump. I purchased it from a clearance dealer not going (radiator was holed, no fuel tank etc.) but was told it should go. I've managed to get it going but it wont hold a steady rpm. It surges continually. Revs climb - then...
    • OzMF35
    • Thread
    • Replies: 8
    • Forum: Ford
  4. O

    MF12 baler part no. needed for dog spring

    It's not a standard spring - I'm going to see if I can get one off a new holland baler to fit as they are more readily available here. This is the new holland spring which is similar to the one I need:
  5. O

    MF12 baler part no. needed for dog spring

    Sadly, not in Australia - where I'm located. I can get one ordered in but @ $100 a spring I might try and adapt something else to do the job. :(
  6. O

    MF12 baler part no. needed for dog spring

    Cheers guys, I'd forgotten about that online parts catalog. I'll give the local MF dealer a try first then.
  7. O

    MF12 baler part no. needed for dog spring

    Need to replace the spring on a dog (centre top of the bale chamber) on my MF12 baler. I realise that oem parts are probably no longer available but if someone who has a parts manual could supply me with the part number for this spring I may be able to cross reference it to find something that...
  8. O

    FE35 air in injector pump

    Yep, it was the lift pump. Did the 2hr dash to my tractor parts guy and picked up a new one, noticed the difference when priming immediately. Finished cutting my hay paddock and it didn't miss a beat!
  9. O

    FE35 air in injector pump

    Ok, I've dismantled and cleaned the low pressure side of the fuel system. I haven't replaced the fuel filters yet as I'm not near anywhere at the moment that I can get them. But was told they were new when I purchased the tractor and its only done 80hrs since then, so I cant see they'd be the...
  10. O

    FE35 air in injector pump

    My FE/MF35 (not sure which it is!) with 23C has a problem at the moment in that I'm constantly getting air in the injector pump, which will cause the tractor to stall. At first I thought it was just due to bouncing over some rough ground, shaking up the fuel and sucking through some air. But...
  11. O

    MF 35 oil bath air filter question

    Mine was gunked up badly when I got it, full of grass seeds and crap. After a good soaking and wash with kero, I set it on fire to burn off all the organic matter stuck in the wire mesh. Then just bang out all the ash, give it another kero wash and its been good since. (Make sure you remove the...
  12. O

    Re: pop up bale loader

    I queried the previous owner about it, as I'll be baling lucerne(alfalfa for you guys) and wasn't sure how'd it'd got with the heavier bales. He reckons heavy bales were fine, reckoned the only trouble he had was doing very light fluffy bales as the fingers couldn't get a decent grip on the...
  13. O

    pop up bale loader

    This is one I picked up locally here in Australia, it looks a bit odd and they don't appear to be as common as the conveyor type, but there were still a few of them here back in the day. I'm yet to put it to use but am told they work quite well! Its badged MF 512
  14. O

    MF35 gear crunch with 2 stage clutch

    I'll check the transmission drain hole, but sounds like its normal for the box. I don't have any real trouble getting it into gear, just a bit of a crunch as it goes. Problem I have is most of the work I do with the tractor requires high range and lots of reverse/forward, like using the rear...
  15. O

    MF35 gear crunch with 2 stage clutch

    Is it normal for the gears to crunch a little when putting it into gear with the clutch half way depressed(ie. pto still engaged?) Changing gears 'on the go' is smooth, but from a standing start I always get a slight crunch as it goes in, either forward or reverse. It hasn't bothered me but...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top