(800) 853-2651
SHOP NOW

Recent content by P T Farmer

  1. P

    440 Skidder

    Yes, I think I could take the carb apart blindfolded hanging upside down! I keep thinking the pressure is too high from the fuel pump. Using the jerry can in the back raises the height of the fuel, easier for the pump to draw then possibly increasing pressure? I'm not sure.
  2. P

    440 Skidder

    Hi folks, been awhile since I've posted anything, good luck I guess. But my luck has run out! I have a 1969 JD 440 skidder, 4 cylinder gas, engine is a 180, same as 2010 tractor and many others. It has worked very well, rebuilt the motor about 10 years ago and brought its power back nicely. But...
  3. P

    706 hydraulic problem

    Hi again, thanks for the replies. Oil level is right on, everything else working fine, 3 point hitch will lift a fertilizer spreader full, probably 400-450lbs. I was running a small log loader half way through unloading a load when it lost power. I don't have a testing gauge, I was hoping it may...
  4. P

    706 hydraulic problem

    Hi there, looking for a hand diagnosing a hydraulic problem on my old Farmall 706. I've lost power in my remotes and I have tried replacing the pressure relief valve but no change. The pump supplies the remotes and the 3 point hitch and the hitch seems to work fine. Possibly an internal problem...
  5. P

    loader lifting capacity

    Ok, thanks for the replies. I want to use a set of forks on it, I would imagine it will decrease the capacity since you would keep the forks flat instead of rolling the bucket back.
  6. P

    loader lifting capacity

    Hi folks, I have a loader question. I'm wondering what the lifting capacity ( in pounds ) is for a case ih 2255 loader on a 585 or 685? I've done some hunting online and called the local dealer with no luck. Any info would be appreciated.
  7. P

    Farmall parts

    Hello out there. Just wondering if anyone has had any dealings with a parts company called tractor joe? I'd like to get a hydraulic pilot relief valve for my 706 from them but I thought I would investigate first. Let me know. Thanks.
  8. P

    Farmall 706 hydraulic relief valve

    Hi there. I've got low hydraulic pressure on my remotes, not enough to open my Gehl 1310 round baler door, which makes it a bugger to get the bale out! Anyway, Redrunrite has the valve but won't reply to my e-mails, they may not ship to Canada but at least they could let me know. I have been...
  9. P

    Char Lynn hydraulic pump specs.

    Okay, that's great, I'll check the requirements of the loader. The flow should be good but the pressure might be low. Thanks a lot for the info.
  10. P

    Char Lynn hydraulic pump specs.

    Wondering if anybody has pressure and flow info for a Char Lynn hydraulic pump? The pump mounts on the pto and was last used on a super w6 to run a loader. I'm wondering if it will run a small pulp loader. Any info would be great. Thanks.
  11. P

    Farmall M boiling over

    The fins of the rad are clean and clear and I had it filled about an inch over the top of the tubes in the rad. I'll try the touch tests and maybe flush the rad with some type of cleaner. If that doesn't work I'll go deeper. Thanks a lot for the replies.
  12. P

    Farmall M boiling over

    Hi there. After running my M spreading manure the other day it started overheating and boiling over. Of course my temp. gauge isn't working right. The temp. outdoors was about 65f and I was on my 3rd load. Now it was a fair drive in 4th to the field with 1 steep hill, the field isn't flat and I...
  13. P

    Farmall 706 Ipto shaft question

    Ok, that makes sense. I"ve had it apart before and just put in back the way it was but that doesn't mean it was right! When I look at the ipto shaft starting at the gear, I should have the gear, then bearing retainer washer(which I thought was a shim), then bearing, correct? Which way should the...
  14. P

    Farmall 706 Ipto shaft question

    Hi there. I'm wondering if anyone has any solutions for a leaking ipto seal. The inside one seems to be riding on the sealing surface ok but the outer seal is riding right at the edge of the smooth surface. Is there another type of seal, maybe a double lip, I can use to make use of more of the...
  15. P

    706 gas missing when hot

    Hi again. Thanks for the replies. They will give me some things to try. On the manifold, wouldn"t I hear ticking on a cold start?
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top