(800) 853-2651
SHOP NOW

Recent content by Patrick Wood

  1. P

    Need a hexigon shaft for AC disc

    Thanks much. So really nothing special on the material side. no high carbon?
  2. P

    Need a hexigon shaft for AC disc

    Hi, All. I need a 84 inch hexigon shaft for my AC disc. Point to point at 180 degree measure is 1.25 What type of steel are these made out of? Have found some supply houses that have the rod in stock but only up to 6ft. I have a very good welder man that can do the welding.
  3. P

    Ford Jubilee loader?

    I have a ford step-through loader with the front bolster. The frame is used to hold hydraulic oil. Has front mount pump. We had the same type on our Jubilee as a kid asking 300.00 2 spool valve
  4. P

    JD 440 ic bottom rollers

    I bought a 1959 JD 440 oc took it to my mechanic that only works on crawlers and skidsteers He said the bottom rollers look good except for one that should work but should look at replacing it or maybe all of them on the one side Final drives are good, bands are new, motor is fine as are...
  5. P

    JD 440 ic 1959

    Hi all again. Thanks for all the info. I have owner's and service manual on order. I would like to change all fluids while waiting for those manuals. Am I correct in thinking that the hydraulics and transmission use the same type of oil, like the n series tractors? What bout the motor? 15...
  6. P

    JD 440 crawler

    This machine has a 5 speed transmission it has a side lever, lever is on the left side all the way forward gives u one speed and 1 reverse and 5 forward gears at center no gears all the way back gives you 1 forward and 5 reverse is that correct?
  7. P

    JD 440 crawler

    Sorry the pc I was using did not bring up the image. Thanks for the info
  8. P

    JD 440 crawler

    So if one side has too much in how do you go about relieving that pressure? remove the hex headed plug
  9. P

    JD 440 crawler

    I just purchased a 440 crawler and have a few questions. Does the idler wheel assembly just slide on the metal frame? One side the The tract is too tight. Can I let some grease out of the tensioner? If I can How do I do that. How do I grease the rollers. It has the rock guards on it? I know...
  10. P

    Stihl chainsaw hard strart

    I have a Stihl chainsaw that takes about 8 pulls to start. Used to be about 2-3 when new about 5 yrs ago But once started runs fine and I can run it dry, refill and one to two pulls we are up and running. I was thinking of buying a new carb but just don't know. 026 farmboss Thanks to...
  11. P

    anyone by 1690 W Storey Rd, Casa Grande, AZ 85194, USA

    Is there anyone on this site that is close to 1690 W Storey Rd, Casa Grande, AZ 85194, USA ROBERTS TRACTOR CO. LLC I am looking at a certain tractor there and would like to have someone check it out for me.
  12. P

    NH and Fergy parts

    I am wondering if anyone would be interested in some new nh rock guards for a sickle mower and also 2 sickle bars for a NH haybind no welds. I am in the process of cleaning out my brother's garage and am finding a lot of new and used parts. also have a good genny for a Ferguson TO 30 Some...
  13. P

    48 *N skips at high speed

    Hi, All. I have a 48 *N Ford. It starts right up no issues. However at high speed there is a definite skip/miss and it seem under power. No back fire. New plugs/new filter/checked screen in carb/great gas flow. checked spark on all plug/ Bright yellow and large. New coil/points/condensor
  14. P

    Areas with Normal or Extra Hay

    My younger brother has about 200 bales of baleage Located by Gilman, wi
  15. P

    Brush killer

    I have crossbow Might have to use hand pump for diesel To dry here, Taylor County , WI, to spray w/diesel and light. no rain since mid may , may 1/4 inch
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top