(800) 853-2651
SHOP NOW

Recent content by Paul Vander Byl

Yesterday's Tractor Forums
  1. P

    Ford 3000 Camshaft hyd pump gear

    Anyone have any experience with fixing this? It just spins on the end of the shaft so I would assume the Dowel Pin has broke? What are the odds that I could take the broken pin out of the cam shaft and replace this without taking the whole engine apart? Seems to me, if I split it between the...
  2. P

    3000 hyd

    Rod, I believe this is my problem on my new to me 3000 - stuck open and dumping all the oil. Have lift cover off hoping to find clogged filters.. I find the restrictor stuck beyond what the knob can push it and a dump tube that has come loose. Turning the knob had 0 effect as the restrictor...
  3. P

    rrlund - 1365 loader hydraulic pump question

    Since my white 2-60 is the same tractor. I have the white 140 loader on it. Made by KMW. My book says there was also another model for non FWA.. My resovoir is a tank mounted under the left floor panel. Pump is the same as the one pictured. The pump mounts to an adapter plate. 2 plates...
  4. P

    white 2-60 air filter

    Thanks Mitch!
  5. P

    white 2-60 air filter

    I can't get the filter to drop down. I did remove the clip. I can turn it a little bit and push up a little bit but not down.. Should it just pull down? Any tips on how/what to grab it with.. Damn, I bet this thing has never been cleaned out... TIA Paul
  6. P

    Canadian FWA 2-60 KMW 140 Loader

    Where can I get parts for my KMW 140 Loader that was put on Canadian FWA 2-60. I have loader parts manual. Import tractors doesn't carry any. KMW exists today still but I doubt they could help.. Any ideas? Thanks, Paul
  7. P

    clutch / input shaft bearing?

    Will the shift forks just lift in/out? The manual talks about releasing something.. Paul
  8. P

    clutch / input shaft bearing?

    Thank Mitch! Great tip there and thanks for the pictures!
  9. P

    clutch / input shaft bearing?

    Any tips on diagnosing the new noise I have on my white 2-60. I think it may be a bearing on the input shaft or clutch bearing. I also noticed at the same time the bushing on the clutch pedal is gone.. Worse when warmed up/hot. When not moving: - Disengaging clutch will make it go away. -...
  10. P

    FWA engage lever

    I have a White 2-60 FWA with loader. Should be same as white 1370 and oliver / Cockshutt 1356. When is the FWA engaged? When lever is towards the motor or rear end?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top