(800) 853-2651
SHOP NOW

Recent content by Phil Heisey, Harleysville

  1. P

    Cockshutt 30-40-50 fender question ....

    Crazy Horse, You are Welcome!!! Phil
  2. P

    Cockshutt 30-40-50 fender question ....

    Crazy Horse, The L and R clamshell fenders are the same. "30" fenders have shorter angle brackets that are bolted (with spacers on each side) to the axle housings. The 35-40-50 are all the same and have longer angle brackets that are bolted (with spacers on each side) to the axle housings...
  3. P

    cockshutt 40

    Hi, If you have a std. std wide front end, NOT a Heavy Duty "later" wide front end, the 30 hubs and bearings will fit your current front end. We have parts. Phil Heisey 215-256-8651
  4. P

    American Bosch PSB injection pump

    SD Dave, On the Cockshutt built tractors, 40-D6, 50-D, 550-D, 570-D, and 570S Diesel, that use the American Bosch PSB pump, their is a seal on the transfer pump shaft. I have these on stock here. Phil Heisey 215-256-8651
  5. P

    Co-op model C

    Try this number for Warren Wheeler: 502-255-4700 Phil Heisey 215-256-8651
  6. P

    Cockshutt plow Questions

    NE Cowboy, It is a #1230. NO trip bottoms. Phil Heisey 215-256-8651
  7. P

    e3 pto clutch plates

    Hi, Originally, the unit should have had .050 total shims. It could be 5 @ .010 or 1 @.050. I would remove ALL the shims, if you had NO SNAP FEEL AT ALL!! We have the 5 pc. new friction disc/steel spacer plate pak parts on stock here. Phil Heisey 215-256-8651
  8. P

    hercules 198 diesel

    Hi, Valve tappet gap.......... .010 HOT Fuel Nozzle pressure...... set at 2750 pounds Herc. manual says:no adjustment is necessary if this pressure has dropped to 2500 pounds. Phil Heisey 215-256-8651
  9. P

    Cockshutt Hydraulics

    Hi Ivan, We have changed (from an O-Ring) to the correct original square ring that was originally used in the COCKSHUTT 35-thru-570S Hydraulic Pump Re-seal kit. Phil Heisey 215-256-8651
  10. P

    Cockshutt 40 axle seals

    Whiskey, The O-Ring goes on the axle last before installing to hub. The purpose of the O-Ring seal is to prevent oil/grease from following the threads to the outer castle nut. I would replace the inner axle oil seal too, while you have everything apart. Phil Heisey 215-256-8651
  11. P

    Cockshutt 40 axle seals

    Whiskey Bent, The other seal is an O-Ring, Cockshutt Part number TG-9430. Phil Heisey 215-256-8651
  12. P

    E3 restoration parts search

    Hi Chris, I just sent you an e-mail. I will try to call you today. Phil Heisey 215-256-8651
  13. P

    E3 restoration parts search

    Hi mab570diesel, Thanks for posting me as a Cockshutt parts source. Phil Heisey
  14. P

    G3400 hercules

    Hi, G3400 head..........175 ft. pounds for all EXCEPT #11 and #13 on tightening sequence...which are 160 ft. pounds......These two are at each end of the widest end of the head. G3400 mains: "T" stamped caps.........9/16' = front, rear, & intermediate = 130 ft. pounds.........1/2'center main =...
  15. P

    Phil Heisey and others

    Hi Bill, Since your phone message yesterday and my return phone message to you yesterday, I checked my references and believe that 200 pounds including the pallot should be a good estimated weight including the small hubs (used on all the 30 tractors up to model year 1954) and with out the...
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top