(800) 853-2651
SHOP NOW

Recent content by Pistonfarmer

Yesterday's Tractor Forums
  1. P

    Case 641c remote cylinder power

    I think your right. That would make a lot of sense. For my needs right now I will lose it for two way action. Instead of single acting
  2. P

    Case 641c remote cylinder power

  3. P

    Case 641c remote cylinder power

    I’m working on the hitch on my 641c I recently acquired. It’s using the remote cylinder setup to run an external hydraulic cylinder for lifting and dropping the 3 point. It has a bypass off of the hydraulic solenoid and I don’t know what it goes to. I do know with the valve closed I get power up...
  4. P

    26 inch rear rim for case model S

    if you could I would very much appreciate it!
  5. P

    Case 641C

    that's weird, on my phone it displays the picture correctly, on the desktop it shows it upside down :?:
  6. P

    26 inch rear rim for case model S

    Not to far. I have some family in tri cities and pullman
  7. P

    Case 641C

    Was it this one?
  8. P

    26 inch rear rim for case model S

    I’m in Washington state on the wet side of the state
  9. P

    26 inch rear rim for case model S

    Hers the tractor;
  10. P

    26 inch rear rim for case model S

    I’m looking for one or two rims for the rear of my model S. Even if half of it’s bad I’m willing to section it to build a new good rim.
  11. P

    Illinois Mid july any pulls?

    Thats perfect. I'm looking forward to it!
  12. P

    Illinois Mid july any pulls?

    I will only be in town the 10-15. im flying out from Washington state so if there is a fair going on that sounds perfect! how late into the evening will it last usually?
  13. P

    Illinois Mid july any pulls?

    Work is sending me to Tuscola Illinois July 11-15. Any tractor pulls going on around then? Would really like something to do while im out there.
  14. P

    Repower F20 Farmall

    Well i figured out what engine im gonna use, a 195.6 straight 6 OHV from a 64 rambler, this engine was origianlly built by nash as a flat head and then converted for OHV. is a very short straight 6 with 4 main bearings, and a fairly long stroke. IT will be a nice compromise for the 4 cylinder...
  15. P

    Repower F20 Farmall

    That would kill me in shipping but thanks for the offer. theres a guy near me that has a couple 28hp 4 cylinder diesel isuzu motors. wonder how well that would work what was the F20 original HP?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top