(800) 853-2651
SHOP NOW

Recent content by plandon3

Yesterday's Tractor Forums
  1. P

    MF 590 lift cover adjustment tools

    Thank you
  2. P

    MF 590 lift cover adjustment tools

    I would really like to find a drawing with all the measurements for the Massey service tool MF 356 for draft and position control lever adjustments. Thank You
  3. P

    Massey ferguson 188 lift cover adjustments

    I know this from along time ago but if you still have sketches of the #7 tool I would really like to have a copy. Thank you
  4. P

    Massey tools

    I'm looking for tool number 7 in this picture or a drawing with measurements so I can build one. Thanks any help would be great
  5. P

    Got the throttel problem fixed

    I should have add soaked had me shorten the long rod to where the butterfly just would start to open.I could not get it clear down to the last notch in idel but within 2 or 3.Im happy.
  6. P

    Got the throttel problem fixed

    Thanks to to you all
  7. P

    1st third of Throttle Quadrant of n use

    The other thing I found is at wide open outside governor rod does not reach the stop by about 1/8 to 1/4 inch.
  8. P

    1st third of Throttle Quadrant of n use

    If you mean the short rod from crab butterfly to governor,no not till the 8th click
  9. P

    1st third of Throttle Quadrant of n use

    To start Ive rebuilt the carb.all new internals in governor with proper amount of shims,new long and short linkage rods all adjusted to the book. A d the 1st 7 clicks no the quadrant dose not change the RPMs. I'm lost,any help would be great Thanks
  10. P

    Governor problems

    Well I guess I spoke to soon.It ain't fixed That's idel Dang it I don't know what to try next
  11. P

    Governor problems

    I got it fixed.It was the governor or shims.It took 3 shims to do the job. Than k s for all the help
  12. P

    Governor problems

    I'll tell ya I am at my wits end with this thing .It seams like know matter what I do as far as an adjustment goes it's not working.
  13. P

    Governor problems

    Yes I checked the notch and the bolt was in and tite.
  14. P

    Governor problems

    1st pic I s idel 2nd is wide open.Now that is watching the throttle lever on the carb as it just starts to off idel and as it end at wide open.now I can the throttle quadrant lever to the idel stop and to the wide open stop but it doesn't change carb any. Also when the book says make your...
  15. P

    Governor problems

    I noticed on that picture the fork is under the washer I s rite
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top