(800) 853-2651
SHOP NOW

Recent content by plowboy 1

Yesterday's Tractor Forums
  1. P

    tach. repair

    electrical. pt# AL35166 I'm pretty sure the point where one of the shafts sits (a jewel?) is worn out and doesn't let the needle float properly.
  2. P

    tach. repair

    Can anyone recommend a place to get a john deere 2750 tachometer repaired? Thanks
  3. P

    jd 2750 won't go into first

    Well, I hate to own up to this one but.... I wasn't finding any easy answers so I went back out and started staring at it. You can almost see down to the bottom where the linkage ends. Didn't look right. On the outside there is a plastic cover under there, must be for protection. I got...
  4. P

    jd 2750 won't go into first

    Yep, for this old brain it is. It tries to go in, but grinds and pops out, never seems to go all the way.
  5. P

    jd 2750 won't go into first

    Another "minor" problem with the 2750. It won't go into first. Other gears are ok, a little grinding but I guess that's not unusual. Tried adjusting linkage (this is a cab model), no change. I don't use this tractor much myself so I don't know how long it's been doing this. With the help of this...
  6. P

    john deere 2750

    Thanks to everyone for all your help. I tried to post a few replies but couldn't get thru for awhile. I have looked at the diagram, but I'm not sure that's my machine. Will look again. Mine goes from the lever on the right side, across under the dash, then back to the rear. There are 2 (?)...
  7. P

    john deere 2750

    I never adjusted it, but there doesn't seem to be any adjustment left. Seems to be maxed out.
  8. P

    john deere 2750

    We've had this tractor about 3 years now. Runs great, plenty of power but....I can't believe some of the engineering! As just about everyone says, the dash board is a nightmare! Plastic on an old diesel machine just will not hold up. So, my question is, has anyone replaced the parking brake on...
  9. P

    JD 2750

    It is a cab model. I have tried putting either/ or and both levers in neutral...no real difference. Thanks for the replies!
  10. P

    JD 2750

    Here I am again. The "new" jd 2750 has been put to work and it's doing pretty well. It doesn't even know the round baler is back there. My issue is that once the bale is done, I like to put the tractor into neutral while the baler is tying so as not to ride the throw out bearing. It always...
  11. P

    gehl 2600 skid steer

    Not sure what your starter looks like but I"ve had a few that all they needed was a shot of penetrating type oil on the starter shaft and they worked just fine.
  12. P

    removing cast iron wheel from shaft

    A friend of mine has to replace a bearing on his sawmill. It"s a big bandmill. the "wheel" drives the saw blade, it"s about 4" in diameter and the shaft is about 6". The wheel has to come off to gwet the bearing off and then back on .The wheel will not move, even with a 50 ton jack pushing it. I...
  13. P

    splitting rocks

    Thanks for all the ideas! and even the wise cracks! I've been reading about the expanding stuff and would really like to give that a try. Sounds like fun! If i get to it, i will post the results....stay tuned!
  14. P

    splitting rocks

    Does anyone know if abig propane torch will generate enough heat to split rock?
  15. P

    splitting rocks

    Do any of you have suggestions for splitting large rocks? I have burned them in the past with brush piles, but right now i don"t have time for that and can"t really afford to have it blasted or hire a hoe-ram. I thought i could dig it out, got sick of it snagging the haybine. Well, turns out...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top