Recent content by Prez Bush

  1. P

    Generators-Six or 12 Volt??

    It's easy to determine whether a coil is six or 12 volts, but I was wondering if anyone had any specs on a generator as to what ohms resistance would be between the "A" terminal and the "F" terminal. Trying to determine if it is six or twelve volt easily. One I am trying measures 3.9 ohm. Any ideas?
  2. 2

    2010

    how do I , look up how many and number one 2010s were made for a flat platform tractor not the utility
  3. kcm.MN

    Saturday Tractor Pic

  4. Crazy Horse

    Plastic mesh/wool material in fuel tank .....

    Looking at the small engine from an old 2-man hand-held post hole auger. Engine is a small Tecumseh 2-stroke engine that powers it. When I looked inside the gas tank, I noticed it seems to be pretty much filled with what appears to be black plastic mesh, looks like a plastic Brillo pad inside...
  5. R

    Mail box

    Can I find a large Case mail box?
  6. J

    Rain today

    Recieved three inches of rain in two hours. Had two hours of sunshine and now it's starting again supposed to be more flash floods. We have hills here as long as you don't live next to a creek your ok. here is a couple pictures.
  7. 7

    Oil leak

    I had a head gasket change on my 70 diesel now I have a small amount of oil dripping out of the exhaust while idle any ideas
  8. F

    Kohler k241-k321 parts

    Anybody need any parts for K241-K321 Kohler? I have a complete 321 that needs rebuilt, heads, cranks, bearing plates, gaskets, valves cam covers, oil pans and alot more! Located in IN and willing to ship. Just message me here THX. I do not have anything for below 10hp and above 14 hp. No twin parts!
  9. S

    m&w rc456 hay rake seal

    does anyone have a part manual or diagram of the hay rake? bearing went out in the rear wheel (tine wheel not tire wheel). i have the bearings but no seal. all that was left of the old one was a metal washer with a rubber ring, is that all there is to them or had it done broke apart and some of...
  10. R

    Basic question - why do we measure gap in points?

    Okay. I remember being taught to measure the points gap many years ago in shop class. I guess I never bothered to ask Why? Is it a timing mechanism to make sure the coil has time to charge/discharge or just what? It has to be more important than simply breaking continuity if we need to measure it.
  11. S

    John Deere 530 baler tension pressure

    Does anyone know the actual pressures in numbers indicated by the green and red gauge on these balers? I have replaced my inop colored gauge with a 5000# gauge and am getting 1000# on the gauge after I close the gate. What pressures are ideal and or acceptable? Thanks in advance for any help...
  12. M

    price jump, did I miss something?

    I was in TSC today. I need 10 gallons of 80W-90. $64.95 for 5 gallons, WOW. Last time I looked it was under $40.
  13. W

    engine studs no good TO35

    Hi, All, cant get the double ender studs out of the old cracked block and they are corroded anyway. The short 7/16 studs are easy to buy but the 10 long ones I cant find; and reason not to substitute grade 8 cap screws for the long studs? thanks BIll
  14. J

    Looking for MM Part

    Jet star 3 Has 2 levers under seat to control the hydraulic flow. One is broken anyone got one?
  15. M

    Rick Deere 34 wheel centers and rims

    I want to thank Rick Cohn for such a good deal on the 34" wheel centers and rims I will look forward to working with him again. Too bad we lived closer so you could see the results after these wheels are on my pulling tractor.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top