(800) 853-2651
SHOP NOW

Recent content by rancherman

Yesterday's Tractor Forums
  1. R

    Mike M, or any body with JD starter hints! (propane)

    Good question on the ring gear. My FIL has a 4010 split as-I-type.. I need to run up there and measure the inside diameter of his propane ring gear.. and compare it to a 4430 flywheel I have laying around. It APPEARS a diesel flywheel would fit in the housing, if a...
  2. R

    Mike M, or any body with JD starter hints! (propane)

    Mike M, I've seen your posts about converting a gasser 4020 starter to a diesel motor/gasser drive. I've 3 4010's and one 4020 on propane. As expected, I've gone through about a pallet full of starters on these tractors over the past 40 yrs.. I've tried DB electrical's...
  3. R

    Need help for a 6.354 Perkins

    No real leads yet on the 'exact replacement'. the 'stress proof' block used in all tractors and some combines is definitely a good thing.. yours appears to be one. The sides of your block appear to be identical to the tractor version. (smooth) Getting a clear picture...
  4. R

    1105 3pt weak

    I just read where you say the steering gets bad when the lift is all the way up.. regardless of load?? When it's 'up'.. do you hear a lot of hydraulic whining inside the lift cover? If so, you got lift valve issues. might be just a blob of crap in the pressure relief valve...
  5. R

    1105 3pt weak

    I'd try 2 things first. change your filter, and clean the intake screen. Sounds like you are starving the system and the 3 point takes a lot of oil when working. Then check your lift pump output. You aren't going to be happy when replacing that little pump. last new one...
  6. R

    Need help for a 6.354 Perkins

    reason for re-cranking is your crank is 3 bolt. which means it's a keyed crankshaft. The single bolt cranks are splined. My front pulley is splined to match
  7. R

    Need help for a 6.354 Perkins

    you wouldn't by chance be the guy I called a couple days ago??? LOL you are in central Iowa? I called with a couple questions.. single or 3 bolt crank.. block casting number.. and the engine serial? If so, what a small world! I'd need to re crank your motor to make it...
  8. R

    hey COASTALBEND

    did you ever get your 1135 re fitted with a running 354? I just found your post on finding a running combine engine.. and have been through what you may already have found out by now! email is good.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top