(800) 853-2651
SHOP NOW

Recent content by rancherruss1916

Yesterday's Tractor Forums
  1. C

    Lost post ( What happened?)

    There was a post yesterday about snow build up in the sieves right? What happened to that one? Am I dreaming or was it blown up? Duh, maybe the holiday season got to me. :-<
  2. D

    Weak hydraulics on 1750D, What do I look at.

    Well, I am making that 1750 earn its keep and the only issue I am encountering is she just doesnt have very good hydraulics, having a hard time lifting that 15' heavy disk, works slowly at full throttle, but all mid throttle to idle will not lift on bit. Any thing I can check out on this ol...
  3. B

    Case 800B weight

    Could anyone send a copy of the page from the manual showing the dry weight of a Case 800B adjustable front end tractor. I have someone interrested in buying my tractor for scrap weight and I would rather see it used to repair another antique than sitting in a scrapyard, but I dont know how much...
  4. R

    were can i get some block sealer

    hey guys i really dont know what i was thinking, guess i wasnt.lol i absolutly would not put stop leak in anything oil. i have a cracked tranny im jbing right now and i guess thats all im thinking about, or not thinking apparently lol. thanks for keeping ,me in the straight lol
  5. R

    were can i get some block sealer

    just wondering were i can get some block sealer. guess i didnt know there was a such thing. do you guys think that a transmition would warm up enough for this stuff to work . thanks for any info
  6. R

    Bucyrus Erie scraper, were can i find bearings???

    anybody have a good source of chiv bearings for a bucyrus erie 12 yrd cable scraper.
  7. R

    D 8 add on hydrolic steer cluch valve how does it work

    thanks again, after looking at the pics you gave me , i noticed my cat has three hoses that go into the top of the tranny.and your pic only has two going to the cylider. have to kep in mind that this was an add on setup to my cat had manual sticks at one time. shes an oldy lol. 2u model. thanks...
  8. R

    D 8 add on hydrolic steer cluch valve how does it work

    thanks guys for the help, all i had to do was read open and closed hyd system and i t finally clicked, lol ever have a blonde moment. the valve that is on the cat works but is really touchy about how you pull the levers, and i thought id chnge it with one i had off of a loader i scrapped, guess...
  9. R

    bearcat a4 hammermill

    Allen, the one i have uses a flat belt but there are i think four or five diferent places were a flat belt could be run. should there be small belts running between some of these, again there all flat belt pulleys, and none really line up with each other. I figured maybe to turn different speeds...
  10. R

    D 8 add on hydrolic steer cluch valve how does it work

    the two spool vlve on my d8 cat is giving me fits.this is an add on that replaces the two sticks thea open the steering cluches. so i changed it with another one i had not noing that a regular valve like a loader valve will not work. both valves are gresen valves and look identickle but are set...
  11. R

    driving out the master link

    i took the end of a leaf spring i found that an old master pin would fit through, ground the old pin down so it couldnt stick bolted the spring end to the track and heated it with a torch and bent it till it lined up with the pin. big sledge and a torch and youll get it out without any busted...
  12. R

    bearcat a4 hammermill

    yea it has the drag chain. guess what i ws wonting to know is which pulley to run the belt on and how much power i need to turn it
  13. R

    bearcat a4 hammermill

    do any of u guys know anything about a western landroller bearcat hammer mill - feed grinder? i woud like to know as much about it as possible model is beacat a4 i think, thanks for any help
  14. R

    farmall factory wide front

    does anybody have any pics of a factory wide front for m or h farmall i bought a front that will bolt up but not sure what it was for originally , it is not a schwarts, has axle clamps similar to my 460 any help would be great thanks
  15. R

    double 9 mower

    ive mowed for as long as i can remember with either 7 fot jd mowers or 9 foot ih mowers. recently have purchased a double 9 rowse with ih heads.you guys probably arent interested in this newer machinery. but what a thrill to cut 18 feet at a time, i cant keep up with the rake and baler lol.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top