(800) 853-2651
SHOP NOW

Recent content by Randy S.E.-MN

Yesterday's Tractor Forums
  1. R

    Screwed again by Marty2374

    Wardner...What was the title of your thread??? "SCREWED AGAIN BY MARTY2374"! the key word here is "AGAIN"! So you do get screwed again, and you come on here and admit it?? "Fool me once...
  2. R

    Screwed again by Marty2374

    I see that he"s had 7 (SEVEN!!) negatives in the last six months...Man, that"s ALL I would have to know to stay away...
  3. R

    PAINTING WHEELS

    Rick...Go over to Parts and Pieces under "44 H, and you will see how I did it. I used Navistar Silver and Hardener to finish. Napa #33723
  4. R

    practical advice on shimming H differential

    I have learned in doing three of them, that, if you are re-using the old ring and pinion gears, be prepared for alot of gear whine for some time. Your old gears remained quiet, gradually wearing into their present contact pattern. By changing that pattern in going back to original "tight" specs...
  5. R

    O/T any muzzler loader hunter here??

    I use my .54 Cal over-under and lyman .54 pistol for yet a third shot I get two hangfires...never happened yet though...Randy
  6. R

    DAD GUM IT

    It does happen to the best of us doesn"t it T.V. They NEVER break when you"re not using "em. Good Luck...Randy
  7. R

    Good Morning, Who's Up?

    Mornin' all...been up since 4:00. I decided long ago I wasn't gonna let this 'puter start my day (I deal with them all day-automotive). I start my day either on Amateur Radio (-.. . -.- ----- -.-. -.-- .-)or I'll pick up a guitar (one of nine) and then if I'm in the mood, I'll flip this switch...
  8. R

    IH. Cub Cadet/Industrial Yellow and white paint?

    The white should be IH 901. Any urethane w/hardener mix should last a lifetime. I"ve restored my 2 Farmall H"s in the last year and a half, and used enamel/hardener...I am not happy with the durability of this stuff. You WILL pay more for Urethane however.
  9. R

    M Water Pump Packing Nut

    I just went through that nightmare. I've done several H's, but not an M. I actually had to replace the shiev (sp) that had previously broke off in two pieces. That "Gland Nut" as IH calls it can be a real bear if it's been bottomed out. I went to every extent to remove ths bugger with what I had...
  10. R

    Hay Rakes

    Is there any difference or disadvantages between a ground driven rake or a pto driven rake. What do you all prefer? Thanks...Randy
  11. R

    multispark problem

    I seem to remember your earlier post regarding the ignition box, and it seems to me you said you had it set on six cylinder mode. I don't know if you have changed this situation, but a four cylinder engine will not run on a six cylinder firing setup as the six cylinder fires every 120 degrees...
  12. R

    When to spray

    Thanks guys...info much appreciated. I'll see how long I have access to the sprayer, and make a judgement call...Randy
  13. R

    When to spray

    I have a 5 acre field that has grass and clover on it, but it is heavily infested with wild parsnips, goldenrod, and milkweed. I was about to cut it with my sickle mower. A good friend just offered up his Walsh sprayer to go over the field with. Is it best to spray while all is still standing...
  14. R

    H rear light what do I have here?

    What kind of seat assembly is that...I've never seen one like that before. Aftermarket???
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top