(800) 853-2651
SHOP NOW

Recent content by rcamaro86

Yesterday's Tractor Forums
  1. R

    allis d17 governor replacement

    how do i replace the weights on my allis d17 governor can i pull it out the front or take the distributor out and pull it from the back . thanks
  2. R

    have a allis chalmers wd need help

    I read that after #1001 they did use shimes is that right or do shime the rods and crank on all of them with stock rods
  3. R

    have a allis chalmers wd need help

    I am in ohio that's a little to far to come and get the motor thanks any way looks like I am going to just rebuild what I have
  4. R

    have a allis chalmers wd need help

    thanks for the info I have the 12 volt alt. already where is the best place to get info in how to shime the rod bearings . so your saying to get the rebuilt kit for a d17 and get the bearings for the 45 crankshaft . it has the spin on oil filter on it is that what I need .
  5. R

    have a allis chalmers wd need help

    would it be a big job to put a gleaner E combine motor in my wd guy has one for sale I found and said it ran when pulled for $600
  6. R

    have a allis chalmers wd need help

    lima ohio
  7. R

    have a allis chalmers wd need help

    I seen that I checked on bearings and was told the crank will need turned is that true
  8. R

    have a allis chalmers wd need help

    sounds like I need to just fine wd45 motor and rebuild it or just keep what I got and rebuild it for it was getting the job done for me thanks
  9. R

    have a allis chalmers wd need help

    could I just the parts off my wd and just do the crank and pistons or add all the other parts to make it run right
  10. R

    have a allis chalmers wd need help

    I have a allis chalmers wd and spun a rod bearing crank is to far gone to turn . can I put a crank from a wd45 in this wd block and will I have to change rods also and use wd45 pistons was told they are the same block different stroke didn't know if the rods are the same size as the wd...
  11. R

    250 ford baler

    This message is a reply to an archived post by chrisinsoky on March 22, 2010 at 17:22:23. The original subject was "Re: 250 ford baler". looking for a manual for my 250 ford baler . where can i get one at ? thanks rick
  12. R

    three piont lift arms don't go down

    took off both side covers and drained the fluid last night i couldn't get the lever to go all the way down and tried by pushing the lever back from inside the case and nothing happen . today go out and the lever goes all the way down and i went in on the left side and pushed the lever...
  13. R

    three piont lift arms don't go down

    i am trying to get my three point lift arms to go down on my 8n . treid with it running and have let it set and have not gone down . what do i need to do . when i start the tractor up they always go up .
  14. R

    8n three piont arms won't go down

    i have a 8n tractor and when i start up my tractor the arms on the three pint go up and i can"t get them to go back down . what do i need to do or is something worng with the unit ? have tried to get them to go down and have let the tractor set and they just stay up .
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top